IEI Technology IMB-ADL-H610 Скачать руководство пользователя страница 66

Страница: 66 / 154

IMB-ADL-H610 Micro ATX Motherboard

Page 66

4.1

Anti-Static Precautions

WARNING:

Failure to take ESD precautions during the installation of the IMB-ADL-

H610 may result in permanent damage to the IMB-ADL-H610 and

severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the IMB-ADL-H610. Dry climates are especially susceptible to ESD. It is therefore

critical that whenever the IMB-ADL-H610 or any other electrical component is handled, the

following anti-static precautions are strictly adhered to.

▪

Wear an anti-static wristband

: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

▪

Self-grounding

: - Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

▪

Use an anti-static pad

: When configuring the IMB-ADL-H610, place it on an

anti-static pad. This reduces the possibility of ESD damaging the IMB-ADL-

H610.

▪

Only handle the edges of the PCB

: - When handling the PCB, hold the

PCB by the edges.

4.2

Installation Considerations

NOTE:

The following installation notices and installation considerations should

be read and understood before installation. All installation notices must

be strictly adhered to. Failing to adhere to these precautions may lead

to severe damage and injury to the person performing the installation.

Содержание IMB-ADL-H610



























































































































































Результаты поиска

Содержание IMB-ADL-H610

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology IMB-ADL-H610, Руководство пользователя

Результаты поиска

Содержание IMB-ADL-H610

Отзывы:

Бренды по названию

Популярные бренды