IEI Technology IMB-ADL-H610 Скачать руководство пользователя страница 114

Страница: 114 / 154

IMB-ADL-H610 Micro ATX Motherboard

Page 114

➔

SYS_FAN1 Start PWM

Use the

SYS_Fan1 Start PWM

option to set the PWM start value. Use the + or

– key to

change the value or enter a decimal number between 1 and 100.

➔

Auto mode fan slope PWM

The PWM slope refers to the ratio relationship between the fan speed and the temperature.

When the temperature rises or falls by 1°C, the fan speed increases or decreases

accordingly. Changing the slope requires entering a number between 1 and 8.

➔

CPU_FAN2 Smart Fan Control [Auto Mode]

Use the

CPU_FAN2 Smart Fan Control

option to configure the CPU Smart Fan.

➔

Manual Mode

The fan spins at the speed set in Manual Mode

settings.

➔

Auto Mode

EFAULT

The fan adjusts its speed using Auto Mode settings.

➔

SYS_FAN2 Start Temperature

If the System temperature is between

fan off

and

fan start

, the fan speed change to

fan

start PWM

. To set a value, Use the + or

– key to change the value or enter a decimal

number between 1 and 100.

➔

SYS_FAN2 Off Temperature

If the System temperature is lower than the value set this option, the fan speed change to

be lowest. To set a value, Use the + or

– key to change the value or enter a decimal number

between 1 and 100.

➔

SYS_FAN2 Start PWM

Use the

SYS_Fan2 Start PWM

option to set the PWM start value. Use the + or

– key to

change the value or enter a decimal number between 1 and 100.

Содержание IMB-ADL-H610



























































































































































Результаты поиска

Содержание IMB-ADL-H610

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology IMB-ADL-H610, Руководство пользователя

Результаты поиска

Содержание IMB-ADL-H610

Отзывы:

Бренды по названию

Популярные бренды