IEI Technology IMB-ADL-H610 Скачать руководство пользователя страница 147

Страница: 147 / 154

IMB-ADL-H610 Micro ATX Motherboard

Page 147

CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Only

certified engineers should replace the on-board battery.

Dispose of used batteries according to instructions and local

regulations.

▪

Outside the European Union–If you wish to dispose of used electrical and

electronic products outside the European Union, please contact your local

authority so as to comply with the correct disposal method.

▪

Within the European Union–The device that produces less waste and is

easier to recycle is classified as electronic device in terms of the European

Directive 2012/19/EU (WEEE), and must not be disposed of as domestic

garbage.

EU-wide legislation, as implemented in each Member State, requires that waste

electrical and electronic products carrying the mark (left) must be disposed of

separately from normal household waste. This includes monitors and electrical

accessories, such as signal cables or power cords. When you need to dispose of

your device, please follow the guidance of your local authority, or ask the shop

where you purchased the product. The mark on electrical and electronic products only

applies to the current European Union Member States.

Please follow the national guidelines for electrical and electronic product disposal.

Содержание IMB-ADL-H610



























































































































































Результаты поиска

Содержание IMB-ADL-H610

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology IMB-ADL-H610, Руководство пользователя

Результаты поиска

Содержание IMB-ADL-H610

Отзывы:

Бренды по названию

Популярные бренды