IEI Technology AFOLUX AFL-315AW/B Скачать руководство пользователя

Страница: 143 / 198

AFOLUX Kiosk Application Series

Page 127

USB 2.0 Controller [Enabled]

The

USB 2.0 Controller

BIOS option enables or disables the USB 2.0 controller

Disabled

USB EHCI function disabled

Enabled

(Default) USB

function

enabled

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded onto the system.

Disabled

Legacy USB support disabled

Enabled D

EFAULT

Legacy USB support enabled

Auto

Legacy USB support disabled if no USB devices are

connected

USB2.0 Controller Mode [HiSpeed]

Use the

USB2.0 Controller Mode

option to set the speed of the USB2.0 controller.

FullSpeed

The controller is capable of operating at 12Mb/s

HiSpeed D

EFAULT

The controller is capable of operating at 480Mb/s

6.4 PCI/PnP

Use the PCI/PnP menu (

BIOS Menu 13

) to configure advanced PCI and PnP settings.

Содержание AFOLUX AFL-315AW/B







































































































































































































Результаты поиска

Содержание AFOLUX AFL-315AW/B

Отзывы:

Похожие инструкции для AFOLUX AFL-315AW/B

Бренды по названию

Популярные бренды

IEI Technology AFOLUX AFL-315AW/B, Руководство пользователя

Результаты поиска

Содержание AFOLUX AFL-315AW/B

Отзывы:

Похожие инструкции для AFOLUX AFL-315AW/B

Бренды по названию

Популярные бренды