IEI Technology AFOLUX AFL-315AW/B Скачать руководство пользователя страница 125

Страница: 125 / 198

AFOLUX Kiosk Application Series

Page 109

bi-directional communication between the system

and the parallel port device and the transmission

rates between the two are much faster than the

Normal mode.

ECP+EPP

The parallel port operates in the extended

capabilities port (ECP) mode. The ECP mode

supports bi-directional communication between the

system and the parallel port device and the

transmission rates between the two are much faster

than the Normal mode

The parallel port is also be compatible with EPP

devices described above

Parallel Port IRQ [IRQ7]

Use the

Parallel Port IRQ

selection to set the parallel port interrupt address.

IRQ5

IRQ5 is assigned as the parallel port interrupt address

IRQ7 D

EFAULT

IRQ7 is assigned as the parallel port interrupt address

Serial Port3 Address [3E8]

Use the

Serial Port3 Address

option to select the base addresses for serial port 3

Disabled

No base address is assigned to serial port 3

3E8 D

EFAULT

Serial port 3 I/O port address is 3E8

2E8

Serial port 3 I/O port address is 2E8

2E0

Serial port 3 I/O port address is 2E0

Содержание AFOLUX AFL-315AW/B







































































































































































































Результаты поиска

Содержание AFOLUX AFL-315AW/B

Отзывы:

IEI Technology AFOLUX AFL-315AW/B, Руководство пользователя, Страница: 125 / 198

Результаты поиска

Содержание AFOLUX AFL-315AW/B

Отзывы: