IEI Technology AFOLUX AFL-315AW/B Скачать руководство пользователя

Страница: 109 / 198

AFOLUX Kiosk Application Series

Page 93

F1 key

General help, only for Status Page Setup Menu and Option

Page Setup Menu

F2 /F3 key

Change color from total 16 colors. F2 to select color

forward.

F10 key

Save all the CMOS changes, only for Main Menu

Table 6-1: BIOS Navigation Keys

6.1.3 Getting Help

When

is pressed a small help window describing the appropriate keys to use and the

possible selections for the highlighted item appears. To exit the Help Window press

the

key again.

6.1.4 Unable to Reboot After Configuration Changes

If the computer cannot boot after changes to the system configuration is made, CMOS

defaults. Use the jumper described in

Chapter 5

6.1.5 BIOS Menu Bar

The

menu bar

on top of the BIOS screen has the following main items:

Main

Changes the basic system configuration.

Advanced

Changes the advanced system settings.

PCIPnP

Changes the advanced PCI/PnP Settings

Boot

Changes the system boot configuration.

Security

Sets User and Supervisor Passwords.

Chipset

Changes the chipset settings.

Power

Changes power management settings.

Exit

Selects exit options and loads default settings

The following sections completely describe the configuration options found in the menu

items at the top of the BIOS screen and listed above.

Содержание AFOLUX AFL-315AW/B







































































































































































































Результаты поиска

Содержание AFOLUX AFL-315AW/B

Отзывы:

Похожие инструкции для AFOLUX AFL-315AW/B

Бренды по названию

Популярные бренды

IEI Technology AFOLUX AFL-315AW/B, Руководство пользователя

Результаты поиска

Содержание AFOLUX AFL-315AW/B

Отзывы:

Похожие инструкции для AFOLUX AFL-315AW/B

Бренды по названию

Популярные бренды