IDT 5P49V6965 Скачать руководство пользователя | Manualshive

Страница: 7 / 58

background image

7

©2018 Integrated Device Technology, Inc.

August 30, 2018

VersaClock

®

6E Family Register Descriptions and Programming Guide

OTP Control Register

The I

2

C slave address can be changed from the default 0xD4 to 0xD0 by programming the I2C_ADDR bit D0. Note that the I

2

C address

change occurs on the I

2

C ACK of the write transaction. An I

2

C write sequence to register 0x00 that changes the value of I2C_ADDR bit

D0 should be followed by an I

2

C STOP condition. Further I

2

C transactions to the part use the new address.

In the OTP Control Register (

) bits can be set for the OTP Burn and OTP Trim status, VC6E or MEMS use and I

2

C address setting.

Four bits are left unused.

* The trim values are commonly written with default values and the OTP_TRIM bit is left at “1”.

Factory Reserved Registers for Internal Use Only

* Configuration Lock bits can be used to prevent future OTP burning that can modify OTP content.

Table 7. RAM0 0x00 – OTP Control Register

Bits

Default Value

Name

Function

D7

1

OTP_burned

It's an active low state that indicates all the OTP burn process is done.
D7 = 1 tells the chip that OTP is not burned and it will run the default mode.
D7 = 0 tells the chip that OTP is burned and it will transfer OTP content to the registers for
operating settings.

D6

1

OTP_TRIM

An active low state that indicates OTP trim part is burned.*

D5

1

Unused

Unused.

D4

1

Unused

Unused.

D3

1

Unused

Unused.

D2

1

Unused

Unused.

D1

1

Unused

Unused.

D0

1

Device I2C_ADDR

If I2C_ADDR = 0 then D0 and if I2C_ADDR = 1 then D4.

Table 8. RAM0 – 0x01: Factory Reserved Bits - Device ID for Chip Identification

Bits

Default Value

Name

Function

D7

1

CFG0_LOCK*

Set to “0” to disable burning OTP of Configuration 0.

D6

1

CFG1_LOCK*

Set to “0” to disable burning OTP of Configuration 1.

D5

1

CFG2_LOCK*

Set to “0” to disable burning OTP of Configuration 2.

D4

1

CFG3_LOCK*

Set to “0” to disable burning OTP of Configuration 3.

D3

1

Unused

Unused.

D2

1

Unused

Unused.

D1

1

Reserved

Factory reserved, leave at “1”.

D0

1

Reserved

Factory reserved, leave at “1”.

«
...
5
6
7
8
9
...
»

Содержание 5P49V6965



























































Отзывы:

Нет отзывов

Похожие инструкции для 5P49V6965

VLT AQUA Drive FC 202

Бренд: Danfoss Страницы: 124

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 114

Бренд: Danfoss Страницы: 24

ECL Comfort 296

Бренд: Danfoss Страницы: 159

VLT AutomationDrive FC 301

Бренд: Danfoss Страницы: 78

Бренд: Danfoss Страницы: 20

Бренд: Danfoss Страницы: 64

Бренд: Kärcher Страницы: 4

Бренд: Davey Страницы: 12

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Nibe Страницы: 20

Network Device NXC-8160s

Бренд: ZyXEL Communications Страницы: 67

DMX-LED-DIMMER X9 HR

Бренд: DMX4ALL Страницы: 14

Бренд: Washify Страницы: 25

Бренд: microHAM Страницы: 64

Бренд: Oilon Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды