IDS 805 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 38

IDS 805 Скачать руководство пользователя страница 8

Connecting Magnetic Contacts and Panic Buttons to a Zone

Tamper connection

Programmable Outputs

Outputs are used to trigger other devices, with a positive 12V. The output can be either set to pulse

or latch.

Definition:

1.

Pulse is when the output will go from no voltage up to 12V and with no intervention goes

back to no voltage. Like a spring if you compress it and then leave it alone it automatically

uncompresses.

2.

Latch is when the output will go from zero to 12V and stay there until something else tells it to

go back to zero volts, like a light switch.

Serial Output (805S Only)

The serial connection outputs an IDS serial protocol that can communicate to any device which has the

protocol implemented. The serial connector can also be used to upload and download settings via

IDSwift2 and the IDS USB to Serial convertor.

Ground

Serial Connector

Rx

Tx

Magnetic Contact
(NC)

Panic Button
(NO)

The diagram shows a magnetic contact (NC) and a panic button (NO)
connected to a zone

3K3

3K3

LED connected to output

Radio connected to output

«
...
6
7
8
9
10
...
»

Содержание 805







































Отзывы:

Нет отзывов