IDS 805 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 38

IDS 805 Скачать руководство пользователя страница 18

Location 22 – 40: Programmable Output Options

Outputs are used to trigger many different devices, the most common being a radio transmitter which

transmits signals back to the alarm monitoring company.
The IDS 805 has 5 positively triggered outputs. Each output triggers with, direct current (DC) 12V and

can supply approximately 100mA of current. If more current is required please use a 12V positively

triggered relay to supply current from a different power source.
Outputs can be set to pulse or latch.
Pulse: The output will rise from 0V to 12V remain at 12V for 3 seconds and return to 0V.
Latch: The output will rise from 0V to 12V and remain in this state until another trigger forces it to go

back to 0V. A light switch is an example of latching as once switched on the light will only go off

again when the switch is returned back to the off position.

Output

Value

Pulse

Latch High

Latch Low

1

1

6

11

2

2

7

12

3

3

8

13

4

4

9

14

5

5

10

15

Locations and their default values

Location Event

Value Action Output

Explanation

22

Alarm

2

Pulse

2

Burglar alarm registered

23

Panic

1

Pulse

1

Panic triggered

24

Low

Battery

0

Battery needs checking

25

Auto-test

0

Panel does a test to the monitoring company

26

Duress

1

Pulse

1

A duress code can be entered

27

AC Fail

0

Alarm loses the 16V AC

28

Close

(Arm)

8

Latch

on

3

Away armed

29

Open

(Disarm)

13

Latch

off

3

Alarm is disarmed

30

AC

Restore

0

16V AC is restored

31

Cancel

0

The alarm has triggered and a valid user code has

been entered

32

Fire

0

Triggered when the [F] key is pressed or a fire zone

triggers

33

Medical

0

[M] key is pressed

34

Strobe

0

This output will latch when an alarm is registered

and will only unlatch once a valid user code is

entered

35

Tamper

0

If tamper per zone or a zone is made a tamper

zone and the tamper condition is triggered will this

output be triggered

36

Silent

Panic

1

Pulse

1

The siren will not sound but this output will trigger

once programmed to alert the monitoring

company.

38

Chime

0

If a chime zone is triggered in the unarmed state,

this output will trigger

39

Communi

cation

Fail

0

If the alarm cannot communicate via the phone

line, this output can trigger another device to alert

the monitoring company of a problem

«
...
16
17
18
19
20
...
»

Содержание 805







































Отзывы:

Нет отзывов