FDX-32 Users Guide
91
HDBaseT scan converter output board
Video
Number / Signal
2 outputs (*13) / HDBaseT / HDMI Deep Color (*14) / DVI 1.0 / HDCP 1.4 (*12)
- TMDS single link
- TMDS clock: 25 MHz to 225 MHz
Connector
2 RJ-45 (*4)
Formats
480i / 480p / 576i / 576p / 720p / 1080i / 1080p (*15)
VGA / SVGA / XGA / WXGA (1280x768) / WXGA (1280x800) / Quad-VGA / SXGA / WXGA (1360x768) /
WXGA (1366x768) / SXGA+ / WXGA+ / WXGA++ / UXGA / WSXGA+ / VESA1080 / WUXGA / QWXGA
* VESA1080 / WUXGA / QWXGA are output as Reduced Blanking
Audio
Number / Signal
2 outputs / HDBaseT / Multi-channel linear PCM up to 8 channels
- Sampling frequency: 32 kHz to 192 kHz
- Sample size: 16 bit to 24 bit
Connector
2 RJ-45 (*4)
Twisted pair cables
Cat6 UTP/STP straight cable, Cat5e UTP/STP straight cable (*5)
Maximum distance
330 ft. (approx.) / 100 m (*6)
Fiber optic extension output board (*7)
Video
Number / Signal
2 outputs (*13) / Optical signals for extension / HDMI (*8) / DVI 1.0 / HDCP 1.4
- TMDS single link
- TMDS clock: 25 MHz to 225 MHz
Connector
2 SFP modules (2 LC connectors per SFP module)
Formats
480i / 480p / 576i / 576p / 720p / 1080i / 1080p (*15)
VGA / SVGA / XGA / WXGA (1280x768) / WXGA (1280x800) / Quad-VGA / SXGA / WXGA (1360x768) /
WXGA (1366x768) / SXGA+ / WXGA+ / WXGA++ / UXGA / WSXGA+ / VESA1080 / WUXGA
* VESA1080 / WUXGA are output as Reduced Blanking
Audio
Number / Signal
2 outputs / Optical signals for extension / Multi-channel linear PCM up to 8 channels
- Sampling frequency: 32 kHz to 192 kHz
- Sample size: 16 bit to 24 bit
Connector
2 SFP modules (2 LC connectors per SFP module)
Fiber
optic
cable
Suitable cable
Duplex fiber cable, SFP module (2 LC connectors) (*9)
Polishing (*10)
SFP for Multimode: PC (recommended)
SFP for Singlemode: UPC (recommended), SPC supported * APC is not supported
Maximum distance (*11)
Multimode fiber (OM3): Up to 985 ft. (approx.) / 300 m
Multimode fiber (OM4): Up to 3,280 ft. (approx.) / 1 km
Singlemode fiber (OS1): Up to 15,420 ft. (approx.) / 4.7 km
■
SFP Specification
Item
Multimode fiber
Singlemode fiber
Connector
2 LC connectors (Duplex)
Wave length
850 nm (Oxide VCSEL Laser (*))
1310 nm (Fabry-Perot laser (*))
Maximum distance
OM3: 985 ft. (approx.) / 300 m
OM4: 3,280 ft. (approx.) / 1 km
OS1: 2.92 miles (approx.) / 4.7 km
Max. input power
0 dBm
+0.5 dBm
Optical power level
Input
Over -13 dBm
Over -18 dBm
Output
-9 dBm to -2.5 dBm
-8.4 dBm to -3 dBm
*1
This product supports 36 bits/pixel Deep color (12 bit/component). It does not support x.v.Color, 3D, ARC, HEC, and CEC
*2
Transmission distance depends on connected equipment. The information above is maximum transmission distance when a cable made by IDK (AW G24) is used and signals
(1080p 60 Hz 24bit/pixel (8bit/component)) are transmitted (both inputs and outputs of this product). When connected equipment is not matched to this product or other makers'
cables are used, video signal can be unstable or video signals cannot be output, even though transmission distance is within the information above.
*3
It does not support DVI signals with HDCP. If you need to extend DVI signals with HDCP, please use The IDK HDC-TD100 as a transmitter.
*4
RJ-45 connector is only for extending video, audio, power for a receiver, control signals using a Cat5e/Cat6 twisted pair cable. IDK receivers are required. Please do not connect
LAN devices to this connector.
*5
Wiring is straight T568A or T568B. If exceeding 50 m, it is recommended to use a Cat6 cable.
*6
If connected to a device whose status is significantly bad, video signal can be unstable or cannot be output. Check the operation beforehand or contact us.
*7
The IDK OPF-H1000-A must be connected for optical extension input and output cards.
*8
It does not support Deep Color, xvYCC, Lip Sync, 3D, ARC, HEC, and CEC
*9
Please refer to SFP Specification.
*10 It is possible to connect without using the recommended polishing method, but that may cause a change of extension distance ability due t o an increase in return loss.
*11 Max. Extension distance is measured under following condition; using fiber of recommended polishing m ethod, without connection at the transmission path and not exceeding the
value of allowable bending radius.
*12 It does not support DVI signals with HDCP. If you need to extend DVI signals with HDCP, please use The IDK HDC-RD100 as a receiver.
*13 Scan converter output board uses 2 of 4 channels. Channel numbers are assigned to each connector consecutively. Channel number for unused channel is reserved but not be
able to set.
*14 This product supports 30 bits/pixel Deep color (10 bit/component). It does not support x.v.Color, 3D, ARC, HEC, and CEC
*15 1080p and 1080i are 50 Hz / 59.94 Hz.
*16 Seamless switching with a black frame.
*17 The Anti-Snow function can automatically recover from snow-noise that is a specific symptom of digital signals having HDCP. Mainly, this snow -noise occurs during system
startup. Therefore, this function does not work in case of snow-noise has already occurred before input the signal to IDK switchers or bad quality signal transmission.
*18 The Connection Reset function can fix these problems without physical cable manipulations. This function can work only in this product's output port, which sometimes will not
take effect if another device is between output of this product and display device.
Please contact our Sales Division for power consumption information of each configuration.
