Identiv uTrust 3720F Скачать руководство пользователя страница 9

Страница: 9 / 87

Document Version 1.00

Last revised on

Page 9 of 87

2020-04-10

Reference Manual for uTrust 3720F and uTrust 3721F Readers

Introduction to the manual

2.1.

Objective of the manual

This manual provides an overview of the hardware and software features of the uTrust 372x F

contactless smart card readers (uTrust 3720 F and uTrust 3721 F).

This manual describes in detail interfaces and supported commands available for developers using

uTrust 372x F in their applications.

2.2.

Target audience

This document describes the technical implementation of uTrust 372x F.
The manual targets software developers. It assumes knowledge about ISO 7816, 13.56 MHz contactless

technologies like ISO/IEC 14443, ISO/IEC 15693 and commonly used engineering terms.

Should you have questions, you may send them to [email protected].

2.3.

Product version corresponding to the manual

Product Component

Version

Hardware

0.1

Firmware

1.00 and above

Содержание uTrust 3720F
























































































Результаты поиска

Содержание uTrust 3720F

Отзывы:

Похожие инструкции для uTrust 3720F

Бренды по названию

Популярные бренды

Identiv uTrust 3720F, Справочное руководство

Результаты поиска

Содержание uTrust 3720F

Отзывы:

Похожие инструкции для uTrust 3720F

Бренды по названию

Популярные бренды