9
5.
Lift the hair clipper when cutting so that only a little hair will be cut at a time. This ensures proper control of the
cutting process and prevents the hair clipper from becoming jammed.
6.
Now cut the back area from the base of the neck upwards to just under the ears.
7.3.2 Step 2 – Back of the head
For the back of the head, set the cutting length to approx. 9-15 mm and cut the hair accordingly.
7.3.3 Step 3 – Sides of the head
Use a cutting length of approx. 9 mm to 12 mm for the sides of the head. Depending on the desired haircut, hold the
hair clipper at the desired angle to the head. Now cut the hair at the sides of the head.
7.3.4 Step 4 - Top of the head
1.
Use a cutting length of approx. 9 mm to 12 mm for the top of the head.
2.
The hair on top of the head should be cut against the growing direction. This means from front to back.
However, it is necessary to cut the hair from front to back in particular places.
3.
If you want to achieve a short hair or brush cut, use a cutting length of approx. 3 mm to 6 mm. You may also
use a shorter cutting length.
Cutting hair using the comb (without an attachment comb)
4.
Using the comb or your fingers, lift the hair to be cut and cut it to the desired length from above the hair. Always
cut the hair at the back of the head first. The cutting length can be determined depending on the distance of
your fingers or the comb to the head.
5.
Remove cut hair from the comb regularly and inspect the evenness of the cut. Trim hair that is too long.
7.3.5 Step 5 – Final touches
1.
Use the hair clipper without an attachment comb for the final touches. Work on the contours on the sides of the
neck and in the ears.
2.
In order to cut sideburns straight, hold the hair clipper with the blades facing down.
3.
Place the cutting blade onto the skin at a right angle and cut downwards.
Brush cut, short hair cut and crop cut
1.
Use the longest cutting length (18 mm). Cut from the base of the neck to the crown of the head. Hold the
attachment comb flat against the head and move it slowly over the hair.
2.
Repeat this step from the base of the head to the top. Now cut the hair from the forehead to crown and even
out the cut on both sides.
3.
For a crop cut, we recommend using the attachment comb for cutting the hair on top of the head. You can
achieve better results this way than if you do not use an attachment comb.
4.
Finally, use the smallest cutting length (1 mm) in order to give the hair down to the base of the neck a brush-
form. Make sure the haircut is symmetric. Touch-up the haircut afterwards if necessary. The last step is cutting
the side burns as well as shortening the hairs at the base of the neck.
7.3.6 Beard Trimming
1.
To trim a beard, put on the attachment comb for the desired length and cut the beard hair accordingly. Always
cut the beard hair first with an attachment comb. To touch up the cut, the hair clipper may also be used without
an attachment comb.
8. CLEANING AND CARE
Attention! Turn off the hair clipper prior to each cleaning.
Attention! Do not under any circumstance use alcohol, acetone, petrol, aggressive cleansers, etc. to
clean the plastic parts. Do not use hard brushes or metal objects either.
CLEAN THE HAIR CLIPPER AFTER EACH USE.
1.
Do not recharge the hair clipper
while you are cleaning it.
2.
Take off the attachment comb before cleaning the hair clipper.
3.
The housing of the hair clipper
can be cleaned with a damp cloth. Make sure that no water gets inside the
device.
4.
Never submerge the hair clipper in water!
5.
The attachment combs can be cleaned with water.
6.
Dry off all parts thoroughly before you use the hair clipper
again.
7.
Keep the hair clipper in its original packaging and store it in a cool, dry place that is free from moisture.
8.1 CLEANING THE ATTACHMENT COMB:
1.
Take off the attachment comb.
2.
Push both release switches on the sides of the hair clipper inwards (see
adjacent picture). The cutting blade will automatically move downwards
with a spring action, freeing the power unit area.
3.
Remove all hair from the blades and from the cutting blade with the
cleaning brush (7).
4.
Put a couple of drops of lubricating oil onto the blades. Wipe off excessive
lubricating oil with a cloth.
