IDEC SmartAXIS FT9Z-1A01 Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 393

background image

S

MART

AXIS P

RO

/ L

ITE

U

SER

'

S

M

ANUAL

FT9Y-B1378

6-3

6: HMI F

UNCTION

Basic Operations

This section describes how to use the SmartAXIS buttons.
The SmartAXIS Pro has the (up), (down), (left), (right), (ESC), and (OK) buttons, and these buttons are

used to operate the screens displayed on the LCD.

Pushing the Switches

The operation of the buttons differs by how they are pressed. There are two ways to push the buttons, which are detailed below.

(up),

(down) buttons

Moves the cursor up and down to select menu items. These buttons are also used to modify numeric values and enter passwords.

(left),

(right) buttons

Moves the cursor left and right. These buttons are used to move the cursor while changing digits, entering password, or operating

on the ladder display screen.

(ESC),

(OK) buttons

Confirm menu items with the (OK) button. Return to the previous screen with the (ESC) button.

Press/Hold

Operation

Press (short press)

The switch is pressed for 0.1 seconds or more and less than three seconds and then released.

Press and hold (long press)

The switch is pressed for three seconds or more and then released.

Run
Edit Program
External Memory
Configurations

Device Monitor
Program Monitor
Status Monitor
Error Status

Password:
****

1

0

2

3

.

.

.

1

Line Number:
0000

1

/ 65535

Do you want to
stop PLC?
No
Yes

Stop
External Memory
Device Monitor
Program Monitor

Return to the
previous screen.

Confirm
menu items.

«
...
169
170
171
172
173
...
»

Содержание SmartAXIS FT9Z-1A01










































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAXIS FT9Z-1A01

EASY412-AC Series

Бренд: Eaton Страницы: 12

Бренд: Eaton Страницы: 3

Бренд: Tense Страницы: 2

Cooper Power Systems RLY-800

Бренд: Eaton Страницы: 14

Бренд: Ytc Страницы: 10

Бренд: Siemens Страницы: 4

SIRIUS 3RU5 36 B Series

Бренд: Siemens Страницы: 4

SIRIUS 3RU6116 Series

Бренд: Siemens Страницы: 5

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 7

SIRIUS 3RF22 Series

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 9

Бренд: Siemens Страницы: 9

SIRIUS 3RA1953-2A

Бренд: Siemens Страницы: 8

SIRIUS 3RR2443-1AA40

Бренд: Siemens Страницы: 12

Бренд: Siemens Страницы: 12

SIRIUS 3RR2243-1FA30

Бренд: Siemens Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды