IDEC SmartAXIS FT9Z-1A01 Скачать руководство пользователя страница 194

Страница: 194 / 393

6: HMI F

UNCTION

6-26

MART

AXIS P

/ L

ITE

SER

ANUAL

FT9Y-B1378

Format SD memory card with the SmartAXIS

This section describes how to format the SD memory card in the SmartAXIS. In order to save the log data, format the SD memory

card in the SmartAXIS.

On the standard screen, press the (ESC) +

(OK) buttons.

The system menu is displayed.

Select

External Memory

with the

(up) and

(down) buttons and press the

(OK) button.

Select

SD Card

with the

(up) and

(down) buttons and press the

(OK) button.

Select

Format

with the

(up) and

(down) buttons and press the

(OK) button.

Select

Yes

with the

(down) button and press the

(OK) button.

While the SD memory card is being formatted, the screen below is displayed. When the format is finished, the screen in step 4

is displayed.

Stopped

2012/OCT/10/WED

13:30:40

Run
Edit Program
External Memory
Configurations

Memory Cartridge
SD Card

Stop Access
Format

Do you want to
format SD card?
No
Yes

Содержание SmartAXIS FT9Z-1A01










































































































































































































































































































































































































Результаты поиска

Содержание SmartAXIS FT9Z-1A01

Отзывы:

Похожие инструкции для SmartAXIS FT9Z-1A01

Бренды по названию

Популярные бренды

IDEC SmartAXIS FT9Z-1A01, Руководство пользователя

Результаты поиска

Содержание SmartAXIS FT9Z-1A01

Отзывы:

Похожие инструкции для SmartAXIS FT9Z-1A01

Бренды по названию

Популярные бренды