IDEC SmartAXIS FT9Z-1A01 Скачать руководство пользователя страница 91

Страница: 91 / 393

MART

AXIS P

/ L

ITE

SER

ANUAL

FT9Y-B1378

4-19

4: O

PERATION

ASICS

Start/Stop Operation

This section describes operations to start and stop the SmartAXIS and to use the stop and reset inputs.

Start/Stop Schematic

Start/Stop Operation Using WindLDR

The SmartAXIS can be started and stopped using WindLDR run on a Windows computer connected to the SmartAXIS. When the

Start

button is pressed in the menu bar shown below, start control special internal relay M8000 is turned on to start the

SmartAXIS. When the

Stop

button is pressed, M8000 is turned off to stop the SmartAXIS.

Connect the computer to the SmartAXIS, start WindLDR, and power up the SmartAXIS.

Check that a stop input is not designated using

Configuration

Run/Stop Control

Stop and Reset Inputs

. See "Stop

Input and Reset Input" on page 5-4.

Note:

When a stop input is designated, the SmartAXIS cannot be started or stopped by turning start control special internal relay M8000 on or off.

Select

Online

from the WindLDR menu bar.

The Online tab appears.

Click the

Start

button to start operation, then the start control special internal relay M8000 is turned on.

Click the

Stop

button to stop operation, then the start control special internal relay M8000 is turned off.

The PLC operation can also be started and stopped while WindLDR is in the monitor mode. Select

Online

Monitor

and click the

Start

Stop

button.

Note:

Special internal relay M8000 is a keep type internal relay and stores the status when power is turned off. M8000 retains its previous status

when power is turned on again. However, when the backup battery is dead, M8000 loses the stored status, and can be turned on or off as
programmed when the SmartAXIS is powered up. The selection is made in

Configuration

Run/Stop Control

Run/Stop Selection at

Memory Backup Error

. See "Run/Stop Selection at Memory Backup Error" on page 5-5.

The backup duration is approximately 30 days (typical) at 25°C after the backup battery is fully charged.



Make sure of safety before starting and stopping the SmartAXIS. Incorrect operation of the SmartAXIS may cause
machine damage or accidents.

Caution

The start/stop circuit of the SmartAXIS consists of three

blocks; power supply, M8000 (start control special

internal relay), and stop/reset inputs. Each block can be

used to start and stop the SmartAXIS while the other

two blocks are set to run the SmartAXIS.

Power

Supply

M8000

Stop

Input

Reset

Input

Start

Start Control

PLC

WindLDR

Содержание SmartAXIS FT9Z-1A01










































































































































































































































































































































































































Результаты поиска

Содержание SmartAXIS FT9Z-1A01

Отзывы:

Похожие инструкции для SmartAXIS FT9Z-1A01

Бренды по названию

Популярные бренды

IDEC SmartAXIS FT9Z-1A01, Руководство пользователя

Результаты поиска

Содержание SmartAXIS FT9Z-1A01

Отзывы:

Похожие инструкции для SmartAXIS FT9Z-1A01

Бренды по названию

Популярные бренды