IDEAL Vogue System Gen 2 S15 Скачать руководство пользователя страница 37

Страница: 37 / 80

Installation and Servicing

SECTION 2 - INSTALLATION

OPERATION WITHOUT OUTSIDE SENSOR

When the burner is established the following screen will

be displayed.

The temperature shown will be the actual Flow

Temperature.
At full output, check the gas rate at the gas meter with no

other appliances in use. Refer to Table 2 for gas rates.

Ensure that, with the boiler operating, the dynamic gas

pressure is able to obtain maximum output. Refer to

Table 1.
Set the timer to be off. The burner will go off and the fan

and pump continue to run for 2 minutes. The following

screen will be displayed.

READY

TIMER OFF OR ROOM THERMOSTAT

AND CYLINDER THERMOSTAT OFF

Check the correct operation of all the system controls

by operating each control separately and check that the

main burner responds.

OPERATION WITH OUTSIDE SENSOR

With all the system controls calling for heat, when the

burner is established the following screen will be displayed.

C TO CYLINDER

60°C

15°C

The temperature shown will be the actual Flow

temperature.
At full output check the gas rate at the gas meter with no

other appliances in use. Refer to Table 2 for gas rates.

Ensure that, with the boiler operating, the dynamic gas

pressure is able to obtain maximum output. Refer to Table 1.
Set the timer to be off. The burner will go off and the fan

and pump continue to run for 2 minutes. The following

screen will be displayed.

READY

TIMER OR ROOM

THERMOSTAT OFF

TIMER OR CYLINDER

THERMOSTAT OFF

15°C

Check the correct operation of all the system controls by

operating each control separately and check that the main

burner responds.

2.25 CHECK CH & HW CYLINDER OPERATION

IMPORTANT

The gas input to the burner is regulated by the gas valve according to the air flow produced by the fan. It is NOT user-

adjustable. Any interference to sealed settings on the gas valve will adversely affect operation and render warranty void. For

additional information refer to Section 1.8 Gas SupplY.

INST

ALLA

TION

Содержание Vogue System Gen 2 S15

















































































Результаты поиска

Содержание Vogue System Gen 2 S15

Отзывы:

Похожие инструкции для Vogue System Gen 2 S15

Бренды по названию

Популярные бренды

IDEAL Vogue System Gen 2 S15, Установка и обслуживание

Результаты поиска

Содержание Vogue System Gen 2 S15

Отзывы:

Похожие инструкции для Vogue System Gen 2 S15

Бренды по названию

Популярные бренды