IDEAL Vogue System Gen 2 S15 Скачать руководство пользователя страница 50

Страница: 50 / 80

Installation and Servicing

SECTION 3 - SERVICING

3.10 REPLACEMENT OF COMPONENTS

3.11 FAN REPLACEMENT

1.  Refer to Sections 3.2 & 3.3.
2.  Remove the ignition, detection and earth leads.
3.  Remove the 2 clips securing the gas inlet pipe and

remove the pipe.

4. Remove the fan low voltage and mains connections.
5. Remove the 4 securing nuts retaining the burner/fan

assembly.

6. Remove the assembly from the heat exchanger.
7. To remove the venturi release the 2 securing screws to

gain access for cleaning.

8. When replacing check the sealing gasket is

undamaged or replace as necessary, and secure with

the 2 screws.

9. To remove the fan, first remove the venturi as above

and release the 3 screws securing the fan to the burner.

(

Note a mounting spacer is fitted to the fan outlet on

32kW model only)

10. Replace the fan and refit the venturi checking the

sealing gasket is undamaged or replace as necessary,

and secure with the 2 screws

*Note a noise damper is fitted to the venturi inlet on the

32kW models

*Note a mounting spacer is fitted to the fan outlet on

32kW.

11. Check the operation of the boiler. Refer to Sections

2.24 - 2.27.

When replacing ANY component:

1. Isolate the electrical supply

2. Isolate water connections

3. Turn off the gas supply

4. Remove the front panel

5. Swing the control panel down into the service position

After replacing ANY component check operation of the boiler,

Noise Damper
Fitted only to

32kW model

Mounting Spacer
Fitted only to

32kW model

including gas tightness, gas rate and combustion

test.

IMPORTANT

. when work is complete, the front

panel must be correctly refitted - ensuring that a

good seal is made.

THE BOILER MUST NOT BE OPERATED

WITHOUT THE FRONT PANEL FITTED.

SER

VICING

SER

VICING

Содержание Vogue System Gen 2 S15

















































































Результаты поиска

Содержание Vogue System Gen 2 S15

Отзывы:

Похожие инструкции для Vogue System Gen 2 S15

Бренды по названию

Популярные бренды

IDEAL Vogue System Gen 2 S15, Установка и обслуживание

Результаты поиска

Содержание Vogue System Gen 2 S15

Отзывы:

Похожие инструкции для Vogue System Gen 2 S15

Бренды по названию

Популярные бренды