IDEAL LOGIC+ SYSTEM2 S15 страница 9 Скачать руководство пользователя

Страница: 9 / 72

Installation and Servicing

Section 1 - General

The Boiler has been tested and certified to:

BSEN 15502-1, BSEN 15502-2, BSEN 15502-2-1,

BSEN 60335-1, BSEN 60335-2-102, BSEN 55014-1 and

BSEN55014-2 for use with Natural Gas & Propane.
Detailed recommendations are contained in the following

British Standard Codes of Practice:

BS5440:1

Flues (for gas appliances of rated input not

exceeding 70 kW).

BS5440:2

Ventilation (for gas appliances of rated input

not exceeding 70 kW).

BSEN12828

Heating Systems in buildings: Design for water

based heating systems.

BSEN12831

Heating Systems in buildings: Method for

calculation of the design heat load.

BSEN14336

Heating Systems in buildings: Installation

and commissioning of water based heating

systems.

BS5546

Installation of gas hot water supplies for

domestic purposes (2nd Family Gases)

BS6798

Installation of gas fired hot water boilers of

rated input not exceeding 70 kW.

BS6891

Installation and maintenance of low pressure

gas installation pipework.

BS 7593:2019

Code of practice for the preparation,

commissioning and maintenance of domestic

central heating and cooling water systems.

Health & Safety Document No. 635.
The Electricity at Work Regulations, 1989.

The manufacturer’s notes must NOT be taken, in any way, as

overriding statutory obligations.

IMPORTANT:

This appliance is UKCA/CE certificated for

safety and performance. Do not connect external control devices

directly to this appliance unless recommended in this manual or

Ideal Heating

in writing. If in doubt, please enquire.

Unapproved control devices could invalidate the warranty of this

appliance and infringe the Gas Safety Regulations.

1.6 SAFE HANDLING OF SUBSTANCES

No asbestos, mercury or CFCs are included in any part of the

boiler or its manufacture.

1.7 LOCATION OF BOILER

The boiler must be installed on a flat and vertical internal wall,

capable of adequately supporting the weight of the boiler and

any ancillary equipment.

The boiler may be fitted on a combustible wall and insulation

between the wall and the boiler is not necessary, unless

required by the local authority.

WARNING:

Rear access to the boiler is not permitted.

CAUTION:

Do not fit the boiler outside.

Timber Framed Buildings

Boilers installed in a timber-framed building must comply with

IGE/UP7 +A 2008.

Bathroom Installations

CAUTION:

This appliance is IP20 rated, do not clean

with jets of water.

You may install the boiler in any internal space. The installation

must comply with the current IEE (BS 7671) Wiring Regulations

and the electrical regulations applicable in Scotland.

If the appliance is to be installed in a room containing a bath or

shower then, the appliance must be installed beyond Zone 2,

as detailed in BS7671.

Compartment Installations

A boiler installed in a compartment does not require

ventilation. However, A boiler installed in a compartment must

provide adequate clearances for servicing.
The compartment should also be fitted with a suitable label in

accordance with current standards.

Refer to Section

1.14

Bathroom Installations

[0] Zone 0
[1] Zone 1
[2] Zone 2

[2*] Without the end wall, zone 2 must extend 600 mm from the bath
[A] 600 mm radius from the bath or shower

0010017086-002

600 mm

2250 mm

600 m

Содержание LOGIC+ SYSTEM2 S15









































































Результаты поиска

Содержание LOGIC+ SYSTEM2 S15

Отзывы:

Похожие инструкции для LOGIC+ SYSTEM2 S15

Бренды по названию

Популярные бренды

IDEAL LOGIC+ SYSTEM2 S15, Установка и обслуживание

Результаты поиска

Содержание LOGIC+ SYSTEM2 S15

Отзывы:

Похожие инструкции для LOGIC+ SYSTEM2 S15

Бренды по названию

Популярные бренды