IDEAL LOGIC HIU Direct MT Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 32

IDEAL LOGIC HIU Direct MT Скачать руководство пользователя страница 5

INDIRECT

SPECIFICATION

5

LOGIC HIU

-

Installation & Servicing / Users

2 TECHNICAL SPECIFICATION

OPERATION

Heating

The temperature setting operates on the principle of set point

regulation and can be fixed within application limits.

Heating Set Point: 25 to 75°C
Nom. heating exchanger net output: 15 kW
Secondary circuit: Maximum pressure rating 3 bar Maximum
operating pressure 2.5 bar
Pump: UPM3 Auto L
Pump bypass setting: 0.45 bar
Pressure switch: opening 0.4 bar - closing 0.8 bar
Safety relief valve setting: 3 bar

Safety thermostat: 55˚C ±3

Expansion vessel: 7.5 litre

Optional Under floor heating capability

Heating control circuit is

VOLT FREE

Domestic Hot Water - DHW

The DHW function takes priority over the heating

function controlled by the DHW priority flow switch

(component 10).
Set Point - DHW temperature 42 to 60°C
Domestic hot water: 10 bar

DHW circuit max. flow rate: 18 l/m (0.3 l/s)

Min.flow rate to activate domestic flow sensor: 2.7

l/m ±0.3

Max. Differential pressure on domestic water

modulating valve: Δp 1.65 bar

Min. Differential pressure on domestic water

modulating valve: Δp 0.35 b

ar

Heat exchanger capacity:

Nom. DHW heat exchanger net output: 50 kW -

Logic HIU Indirect 50

Nom. DHW heat exchanger net output: 75 kW -

Logic HIU Indirect 75

Optional Pre heat function

Primary Performance

Maximum working pressure: 16 bar - primary

3 bar - secondary

Maximum temperature: 85°C

Medium: Water

Max. Percentage of glycol 30%

Max. Recommended primary circuit flow rate: 1.2 m³/h

Electrical

Power supply: 230 V (ac)±10% 50 Hz

Power consumption: 80 W

Protection class: IP 40

Actuator: stepper 24 V

Probes: NTC 10 kΩ

Construction

Frame: RAL 9010 sprayed steel

Protective shell cover: PPE

Components: brass BS EN 12165 CW617N

Pipes: stainless steel

Exchanger: brazed stainless steel

LOGIC HIU INDIRECT 75, LOGIC HIU INDIRECT 50

«
...
3
4
5
6
7
...
»

Содержание LOGIC HIU Direct MT

































Отзывы:

Нет отзывов