background image

Auto Passport Installation Guide

Page 1 

Copyright © Innovative Control Systems, Inc.

Installation Overview

Thank you for purchasing your Auto Passport, the ICS® radio frequency identification system. This document was written for technicians 
and electricans installing the Auto Passport. A thorough understanding of electrical wiring, installation, codes, and safety protocols is 
required. No prior experience with the Auto Passport is necessary. By reading the information and performing the procedures in this 
installation guide, you should be able to install the Auto Passport system-level and communications wiring.

NOTE:  

The Auto Passport is not a stand-alone system. WashConnect and a connection to an Auto Sentry is required.

System Components

 

„

The protective enclosure houses the RFID reader and antenna.

 

„

One 

All-In-One RFID Reader / Antenna Enclosure 

per lane is 

to be installed on an overhead truss or canopy above the lane 
near the Auto Sentry flex so vehicles can drive underneath it. 

 

„

The RFID All-In-One Reader/Antenna power and data cable 
terminates at the terminal blocks located in the base of Auto 
Sentry flex.

 

„

The RFID All-in-One Cable is 35’ in length.

Truss Size Information

Trusses are available in two sizes:

 

„

A 95-inch truss to be installed on curbs or raised islands.

 

„

A 100-inch truss to be installed on ground-level surfaces.

This guide should be supplied to the electrician prior to the installation of 
conduits and wiring to ensure the 

Auto Passport 

is installed properly. Faulty 

installations are the major cause of system malfunctions. The 

Auto Passport 

must be installed exactly as described in this installation guide to 
ensure its reliability and safe operation.

WARIGE:

 

Failure to properly install the Auto Passport could result in 

serious injury or death and will void the warranty.

Version Considerations

This version 3.0 of the installation guide, released on November 5, 
2019. WashConnect Software version of 1.6.7 or higher.

Site Planning

Careful planning for the layout of the site will help eliminate possible 
problems with the start-up of your system and will ensure continued, 
reliable system operation. In determining the location stage, keep the 
following objectives in mind:

 

„

The Auto Passport has been designed to operate in an outdoor environment.

Figure 1. All-In-One RFID Reader / Antenna Enclosure

Figure 2. Internal view of Enclosure 

displaying the RFID Reader Card 

Figure 3. RFID All-In-One Cable

Содержание Auto Passport















Отзывы: