background image

xx03DVR: Description
xx03DVR Board assemblies

Figures 4 and 5 show how a 2003, 2303,  or 4803 

Parallel Interface Board with a circuit-side connector 

mounts on the xx03DVR Board.  The Parallel Interface 

Board is positioned over J1 on the xx03DVR Board and 

pressed into place.  A pair of 0.688 high female-to-male 

standoffs holds the front portion of the two boards 

together.  The rear portion is held by the mating force 

of the 64 pin DIN connectors.  Signal and power wires 

are attached to the xx02DVR terminal blocks.  

Figure  5  shows  the  115848  '8003'  type  board 

mounted on the xx03DVR board.  Its height is slightly 

bigger due to the vertical RJ45 connector on the 8003.   

An 8003H will not mate with the 115490 xx03DVR 

Board

A version of the xx03DVR Board is available with 

a female connector on its circuit side so it can sit on 

top of standard 2003, 2303, 4803 and 8003H boards.  

Mounting  the  xx03DVR  Board  on  top  of  standard 

boards adds 0.6 inches to the overall assembly height 

as shown in Figure 3.  

A pair of 0.688 high standoffs holds the two boards 

together.  Standard 8003s with their vertical RJ-45 

connector cannot be used with the 115522 xx03DVR 

Board because the board blocks the RJ45 connector.

Figure 4     xx03DVR Board (P/N 115490) with a 2003, 2303 or 4803 type 

board.  Order connector down versions for the 115490 xx03DVR Board

Figure 6     xx03DVR Driver Board (P/N 115522) on top of a

4803, 2003 or 2303 Parallel Interface Board

Standard Interface Board with component side connector 

1.825

Screw Terminals

4803 GPIB Headers

4803DVR Board

1.237

Screw Terminals

Interface Board with Digital Connector on the circuit-side 

4803DVR Board

Figure 5     xx03DVR Board (P/N 115490) with a 115848 '8003' board.  

Figure 7    xx03DVR Driver Board (P/N 115522) on top of a

8003H Parallel Interface Board

Содержание 03DVR Series

Страница 1: ... standard xx03 Parallel Interface Cards but it sits on top of the Parallel Interface Card covers the I O connectors and and adds to the assembly height xx03DVR Relay Driver Board shown with a 4803 Interface Board Figure 1 ICS xx03 Parallel Interface Board plugs down onto the xx03DVR Board The xx03DVR Board expands the output drive capability of ICS s 40 line ParallelInterfaceBoardsbyaddingheavy du...

Страница 2: ...he lines high to sense open contacts and lines xx03DVR Board Description The xx03DVR Board terminal strip connections are identified by bytes and bit so they easily relate to the signals on the companion Interface Board Standard bit commands like ROUTe CLOSe or ROUTe OPEN can then be used to operate the relay drivers Set the Output polarity to high true for the relay driver signals An External Res...

Страница 3: ...it side so it can sit on top of standard 2003 2303 4803 and 8003H boards Mounting the xx03DVR Board on top of standard boards adds 0 6 inches to the overall assembly height as shown in Figure 3 A pair of 0 688 high standoffs holds the two boards together Standard 8003s with their vertical RJ 45 connector cannot be used with the 115522 xx03DVR Board because the board blocks the RJ45 connector Figur...

Страница 4: ...out low 1 3 volts at 500 mA V max 32 Vdc TTL Signal Characteristics TTL signals have the same characteristics as thecompanionInterfaceBoard sdigitalsignals Inputs typically have 33 Kohm pullups for sensing CMOS signals and contact closures Outputssinkupto48mA Signalscontrollable byInterfaceBoardcommandsoraremonitored by the Questionable Register Number 16 8 or none As inputs High 2 4 Vdc or open L...

Отзывы: