Parallel interface
Standard xx03DVR supplies a male DIN
connector for mounting a 2003, 2303, 4803
or 8003 Interface Board with its Digital I/O
connector on the circuit side. Power supplied
by a switching power supply on the xx03DVR
board.
Supplied Power:
Voltage
+5 ± 0.2 Vdc
Current
500 mA max
Parallel interface Boards
The xx03DVR board supports the following
Parallel Interface Boards
xx03DVR Part Number
Model 115490
115522
2003
116038
2003
2303
114732
2303
4803
114648
4803
8003
115848
8003H
xx03DVR Connections
The following companion Interface Board
lines are used by the xx03DVR Board:
40 Digital I/O lines
Stable Signal
External Reset Input
other interface Board Signals
The following companion Interface board
signals are brought to pads on the xx03DVR
Board and are available to the user:
LED drive signals:
PWR, RDY, TALK, LSTN, SRQ
and ERR
EDR and Inhibit pairs #1 and #2
Status A and Status B inputs
Trigger, Remote and Reset outputs
Data Strobe
xx03DVR: Specifications
Driver Characteristics
High power outputs for driving relays or
other loads. Relay driver outputs controlled by
SOURce or ROUTe commands with polarity
set to high true. Number of lines is 40 less the
number of lines that by-pass the relay drivers
and connect directly to ports 1 and 2 on the
digital board.
Number
24, 32 or 40 Lines
Driver Form Open collector with
anti-backlash diode.
Current
up to 300 mA
Vout low
1.3 volts at 500 mA
V max
32 Vdc
ttl Signal Characteristics
TTL signals have the same characteristics as
the companion Interface Board's digital signals.
Inputs typically have 33 Kohm pullups for
sensing CMOS signals and contact closures.
Outputs sink up to 48 mA. Signals controllable
by Interface Board commands or are monitored
by the Questionable Register.
Number
16, 8 or none
As inputs:
High
> 2.4 Vdc or open
Low
< 0.5 Vdc at 200 µA
Pullup resistor 33 kohms to +5 Vdc
As outputs
High = >3 V with 3 mA source
High =>2 V with 24 mA source
Low = 0.0 to +0.55 Vdc, 48 mA sink
external Reset input
TTL input signal that resets the Interface
Board when pulled to ground. Pullup pro-
vided by a resistor on the companion Interface
Board.
Physical
Size, L x W x H
177.8 x 114.3 x 14.3 mm
(7.0x 4.5 x 0.562 inches)
Assembled dimensions
115490 177.8 x 114.3 x 32.3 mm
7.0x 4.5 x 1.265 inches)
115522 177.8 x 114.3 x 46.36 mm
(7.0x 4.5 x 1.825 inches)
Connectors and Headers
Digital 96-pin, 3 row male DIN
connector using rows A & C.
Relays Screw terminals for
#16 - #30 AWG wire.
Temperature
Operation -10° C to +70° C
Storage -20° C to +85° C
Humidity
0-90% RH without condensation
Power
+7 to + 32 Vdc @ 4 VA (typical)
included accessories
Instruction Manual
2 Standoffs and locknuts
available accessories
None
ORDERING INFORMATION
Part Number
xx03DVR Board for 2003, 2303, 4803 and 8003 boards with circuit-side connectors. Includes Instruction Sheet.
115490
xx03DVR Board for standard 2003, 2303, 4803 and 8003H boards Includes Instruction Sheet.
115522
Copyright 2014 ICS Electronics - Specifications subject to change without notice.
09/16
