45
Computer” followed by the System icon.
2.
Choose the “Hardware” tab, and then click the “Device
Manager” tab.
3.
Click the “+” in front of “SCSI controllers.” “Promise
Technology, Inc. FASTTRAK100 IDE controller” should appear.
2-2 Microsoft Millennium
2-2-1 Installing Drivers during Millennium Installation
The following details the installation of the FastTrak100 drivers
while installing Microsoft’s Millennium (with the FastTrak100
controller card already in place). If you’re installing the
FastTrak100 drivers on a system with Millennium already
installed, see “Installing Drivers with Existing Millennium
System.”
1.
Install Microsoft Millenium fully.
2.
After installation, go the “Start” menu and choose “Settings.”
3.
From the “Settings” menu, choose “Control Panel.”
4.
In the “Control Panel” window, double-click on the “System”
icon.
5.
In the “System” window, choose the “Device Manager” tab.
6.
In the hierarchical display under “Other Devices” is a listing for
“PCI Mass Storage Controller.” Choose it and then press the
“Properties” button.
7.
Choose the “Driver” tab in the “Properties” window, choose
“Update Driver,” and then press “Next.”
8.
Choose “Search for a better driver than the one your device is
using now (recommended),” then press “Next.”
9.
Choose “Specify Location,” then type “A:\WINMILL” in the text
box.
10.
Insert the “FastTrak100 Driver” diskette into drive A:.
11.
Press the “Next” button. A message informing you that
Millennium has found “Windows Millennium Promise
FASTTRAK100 (tm) IDE Controller” should appear.
12.
Press “Next,” then “Finish,” then “Yes” when asked if you
want to restart your computer. Be sure to remove the diskette
from drive A:.
2-2-2 Installing Drivers with Existing Millenium System
The following section details the installation of FastTrak100
drivers on a system that has Millenium already installed and
46
running. If you’re installing the FastTrak100 drivers on a system
during an installation of Millenium, see “Installing Drivers During
Millenium Installation.”
1.
After installing the FastTrak100 controller card and
configuring the hard drives, power up the system and boot.
2.
The “Add New Hardware Wizard” will appear, informing you
that it has found a “PCI Mass Storage Controller.”
3.
Click on “Next,” and from the generated list box, choose
“Search for a better driver than the one your device is using
now.”
4.
Click on “Next,” and from the generated choices, choose
“Specify a location.”
5.
Insert the “FastTrak100 Driver” diskette in drive A:.
6.
Type “A:\WINMILL” in the text box that appears.
7.
Click on “Next.” A message informing you that Millennium has
found “Windows Millennium Promise FASTTRAK100 (tm) IDE
Controller” should appear.
8.
Click on “Next” and then on “Finish”.
9.
Choose “Yes” when asked if you want to restart your
computer.
Be sure to eject the diskette from drive A:.
Confirming Driver Installation in Millennium
To confirm that the driver has been properly loaded in
Millennium,
perform the following steps:
1.
Choose “Settings” from the “Start” menu.
2.
Choose “Control Panel,” and then double-click on the
“System”
icon. Choose the “Device Manager” tab, and then click the “+” in
front of “SCSI controllers.” “Windows Millennium Promise
FASTTRAK100 (tm) IDE controller” should appear.
2-3 Windows 98
5.2-3-1 Installing Drivers During Windows 98 Installation
The following details the installation of the FastTrak100 drivers
while installing Windows 98 (with the FastTrak100 controller
card already in place). If you’re installing the FastTrak100
drivers on a system with Windows 98 already installed, see
“Installing Drivers with Existing Windows 98.”
1.
After installing the FastTrak100 controller card and
configuring the hard drive(s) partition and format your hard
drive(s), if necessary.
