ICP DAS USA IR-310-RM Скачать руководство пользователя | Manualshive

Страница: 25 / 65

background image

IR-310-RM,

IR Controlled 10-ch High Power Relay Module

(Ver. 1.1, Jul/02/2013) 25

4.2.6 Power on value and power failure memory section

If the

“

Enable Power Failure Memory

”

is not set, IR-310-RM applies the Power On

Value  settings  of  10  relay  states.  Otherwise,  the  10  relay  states  of  power  failure
memory are used when power is on.

Radio  buttons  Forward/Stop  of  power  on  value  are  for  the  forward/stop  action  in
sequential mode.

Latency (sec) is the delay time to record the 10 relay states after the relay states are
changed. The default is 1800 sec (30 min) and the minimum is 5 sec.

Figure 4-7: Power on value and power failure memory section.

4.2.7 IR Sensor Selection section

There are three selections of IR sensor sources can be set.
(1) On-board IR sensor: The sensor is located in the front panel.
(2) IR Receiver Cable: Use

“

IR Output

”

channel. CA-IR-001 needs to be

plugged into the

“

IR Output

”

jack (3.5 mm audio jack).

(3) No sensor: Disable the IR remote function.

Figure 4-8: Source of IR sensor.

ГК

Атлант

Инжиниринг

–

официальный

представитель

в

РФ

и

СНГ

+7(495)109-02-08 [email protected] www.bbrc.ru

«
...
23
24
25
26
27
...
»

Содержание IR-310-RM


































































Отзывы:

Нет отзывов

Похожие инструкции для IR-310-RM

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Бренд: Raymarine Страницы: 12

Бренд: Jafar Страницы: 13

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: DayTronic Страницы: 22

Бренд: DayTronic Страницы: 414

Бренд: Samson Страницы: 73

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Parkside Страницы: 86

Бренд: Saftronics Страницы: 13

Бренд: Reliance Foundry Страницы: 3

Бренд: Wesa Страницы: 8

Бренд: Tenpilot Страницы: 2

Бренд: Sartorius Страницы: 165

Бренд: Valence Tech Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды