Icom IC-R2 Скачать руководство пользователя страница 39

Страница: 39 / 40

SPECIFICATIONS AND OPTIONS

• Selectivity

FM, AM

More than 15 kHz/–6 dB
Less than 30 kHz/–60 dB

WFM

More than 150 kHz/–6 dB

• Audio output power

: 100 mW typ. at 10% distortion

(at 3.0 V DC)

with an 8

Ω

load

• SP connector

: 3-conductor 3.5 (d) mm

(

⁄

˝)/8

Ω

Options

BC-127A/D BATTERY CHARGER
Regularly charges 2 or 4 AA (R6) Ni-Cd batteries. 2 Ni-Cd
batteries are supplied with the BC-127A/D.

LC-146 CARRYING CASE
Helps protect the receiver from scratches, etc.

SP-13 EARPHONE
Provides clear receive audio in noisy environments.

HP-4 HEADPHONE
Provides increased readability of signals in noisy environ-
ments and listening privacy.

AD-92SMA ANTENNA CONNECTOR ADAPTER
Allows you to connect an antenna with a BNC connector.
(SMA to BNC adapter)

CS-R2 CLONING SO OPC-478 CLONING
CABLE
Allows you to transfer data from memories, etc. and quickly
and easily edit and store data via a PC.

OPC-474 CLONING CABLE
Used for handheld-to-handheld cloning.

All stated specifications are subject to change without
notice or obligation.

Содержание IC-R2









































Результаты поиска

Содержание IC-R2

Отзывы:

Похожие инструкции для IC-R2

Бренды по названию

Популярные бренды

Icom IC-R2, Инструкция по эксплуатации

Результаты поиска

Содержание IC-R2

Отзывы:

Похожие инструкции для IC-R2

Бренды по названию

Популярные бренды