Icom IC-R2 Скачать руководство пользователя

Страница: 35 / 40

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

REF.

No power comes ON.

• The batteries are exhausted.
• The battery polarity is reversed.

• Replace the batteries.
• Check the battery polarity.

p. 1
p. 1

No sound comes from the
speaker.

• Volume level is too low.
• Different tone is selected with tone squelch.

• Push [VOL

] to obtain a suitable level.

• Check the tone using tone scan.

p. 10
p. 23

Frequency cannot be set.

• The lock function is activated.
• Channel indication mode is selected.

• Push [FUNC] + [

(MODE)

LOCK] to cancel the function.

• Turn the channel indication mode OFF in set mode.

p. 8
p. 29

No beeps sound.

• Beep tones are turned OFF.

• Turn beep tones ON in set mode.

p. 26

Receive audio is
distorted.

• The operating mode is not selected correctly.

• Select a suitable operating mode in set mode.

p. 11

Desired set mode item
cannot be selected.

• The desired set mode item is in expanded set

mode.

• Some set mode items cannot be selected in

the broadcast band.

• Turn the expanded set mode ON.

• Choose a band other than the broadcast band.

p. 25

If your receiver seems to be malfunctioning, please check the
following points before sending it to a service center.

Содержание IC-R2









































Результаты поиска

Содержание IC-R2

Отзывы:

Похожие инструкции для IC-R2

Бренды по названию

Популярные бренды

Icom IC-R2, Инструкция по эксплуатации

Результаты поиска

Содержание IC-R2

Отзывы:

Похожие инструкции для IC-R2

Бренды по названию

Популярные бренды