Icom IC-F62D Скачать руководство пользователя страница 95

Страница: 95 / 125

BIIS 1200 SYSTEM OPERATION

9-4

Transmitting a call

Transmitting a Status Message

You can transmit a preset Status Message� You

cannot transmit a voice call at the same time�

NOTE:

Depending on the presetting, the Priority A

channel is always used to send Status Messages�

(Menu > Signaling/Call >

Call Menu

)

1� Push [Menu] to display the Menu screen�

2� Push [P2 (Up)] or [P1 (Down)] to select

“Signaling/Call,” then push [OK]�

Channel/Scan

►

Signaling/Call

►

3� Push [P2 (Up)] or [P1 (Down)] to select

“Call Menu,” then push [OK]�

Call List Select

►

Call Menu

►

Signaling/Call

4� Push [P2 (Up)] or [P1 (Down)] to select an

Individual or Group ID, then push [OK]�

✔

Station 1

►

✔

Group 1

►

Call Menu

5� Push [P2 (Up)] or [P1 (Down)] to select “Status,”

then push [OK]�

✔

Status

►

✔

Message

►

Station 1

6� Push [P2 (Up)] or [P1 (Down)] to select a Status

Message, then push [PTT] to transmit it�

✔

TX Status 01

✔

TX Status 02

Status

• “Success” is displayed when an acknowledgment is

received from the targeted station�

• “Failed” is displayed if an acknowledgment is not

received from the targeted station�

NOTE:

If the following settings are configured using the

CS-F52D

programming

software

, the Status

Message can be automatically transmitted when:

•The transceiver is turned ON�

Set

Power ON Status 23

to “Enable�”

•The transceiver is turned OFF�

Set

Power OFF Status 19

to “Enable�”

(Analog > BIIS > Config > Status Setting)

TIP:

•You can also transmit a Status Message through

Status

�

(Menu > Signaling/Call >

Status

)

•Push [Status] to directly display the “Status” screen

in step 4 to the left�

•Hold down [Status] for 1 second to transmit the

preset Status Message that is set in the “Status”

screen�

Содержание IC-F62D






























































































































Результаты поиска

Содержание IC-F62D

Отзывы:

Icom IC-F62D, Руководство по эксплуатации, Страница: 95 / 125

Результаты поиска

Содержание IC-F62D

Отзывы: