Icom IC-F62D Скачать руководство пользователя страница 56

Страница: 56 / 125

MENU SCREEN

6-13

Bluetooth

Turns the Bluetooth function ON or OFF�

•

OFF: Turns OFF the function�

•

ON: Turns ON the function�

Bluetooth Reset

Initializes the Bluetooth unit�

Initialization can be done only when the Bluetooth

function is OFF�

Auto Connect

Select whether or not to automatically connect to a

paired Bluetooth device when its power is turned ON�

•

OFF: Does not connect to a paired device�

•

ON: Automatically connects to the last connected

device�

NOTE:

The transceiver connects to the last

connected device if the connecting operation is

performed on the device side, even if this item is set

to OFF�

Audio Select

Selects the AF Output device when a Bluetooth

headset is connected�

•

Only RMT:

Sets the Bluetooth headset as the AF

Output device�

•

RMT & SP: Sets the Bluetooth headset and the

transceiver’s speaker as the AF

Output devices�

Bluetooth info

Displays the installed Bluetooth unit name, address,

supported profile, and its version information.

Device List

Displays the paired Bluetooth devices�

To find other Bluetooth device, select “Find Device.”

See pages 11-4 ~11-5 for details�

Key Bp (VS3)

Sets the beep sound when the optional VS-3

Bluetooth

headset

Custom Key ([PLAY]/[FWD]/

[RWD]) is pushed�

•

OFF: No beep sounds�

•

ON: A beep sounds�

PWR Sv (VS3)

Selects whether to operate in the Bluetooth headset’s

Battery Saving mode when the optional VS-3

Bluetooth

headset

is connected� When the Power

Save is activated, the user cannot use the VOX

function�

NOTE:

When a third-party headset or a data device

is connected, this function is automatically set to

OFF, even if this item has been set to ON�

•

OFF: Turns OFF the function�

•

ON: The Power Save mode is enabled when no

communication or operation is performed for

120 seconds�

PTT Bp (VS3)

Sets the beep sound when [PTT] is pushed on the

optional VS-3 Bluetooth

headset

�

•

OFF: No beep sounds�

•

ON: A beep sounds�

1 Touch PTT

Sets the One-Touch PTT function when the Bluetooth

headset is connected� The function enables a user to

transmit without continuously holding down [PTT]�

NOTE:

When a third-party headset is connected, this

function may automatically be set to ON, even if this

item has been set to OFF�

•

OFF: Push [PTT] to transmit, release to receive�

•

ON: Push [PTT] to transmit, push again to receive�

Wait to Pair

Enters the pairing request wait mode� The transceiver

waits for a pairing request from a Bluetooth device�

Bluetooth

Содержание IC-F62D






























































































































Результаты поиска

Содержание IC-F62D

Отзывы:

Icom IC-F62D, Руководство по эксплуатации, Страница: 56 / 125

Результаты поиска

Содержание IC-F62D

Отзывы: