Icom IC-F62D Скачать руководство пользователя страница 20

Страница: 20 / 125

PANEL DESCRIPTION

2-13

Category: Functions (Continued)

AquaQuake™

While holding down this key, the AquaQuake water

draining function removes water from the speaker grill

by vibrating the internal speaker�

Water in the speaker grill may muffle the sound coming

from the speaker�

NOTE:

• After the specified period of time, this function

automatically stops, even if a user continues to hold

down this key�

• This key works with only the internal speaker�

Category: GPS
GPS Position

Push to display the “GPS Position” screen in the

Menu mode�

Category: Voice Recording
Call Recorder

Push to start or stop the voice recording�

Last Call Play

Push to playback the last recorded audio file.

Play Call Record

Push to display the “Play Call Rec” screen�

See page 10-3 for details�

Category: Audio Setting
TX Noise Cancel

Push to select the TX Noise Cancel level between 1

and 3 to suppress the microphone input noise to make

the audio easy to hear�

When “OFF” is selected, the microphone input noise is

not suppressed�

RX Noise Cancel

Push to select the RX Noise Cancel level between 1

and 3 to suppress the receive audio noise to make the

audio easy to hear�

When “OFF” is selected, the receive audio noise is not

suppressed�

Category: Bluetooth
Bluetooth

Push to turn the Bluetooth

function ON or OFF�

Waiting Pairing

Push to enter the Pairing Request Wait mode�

• The transceiver waits for a pairing request from a

Bluetooth

device�

Category: Vibration
Vibration

Push to turn the Vibration function ON or OFF�

When “ON” is selected, the transceiver vibrates when a

matching call or ID is received�

Category: Display
Backlight

Push to select the Backlight level�

•

OFF

: The backlight is always OFF�

•

: The backlight is always ON�

•

Auto

: When any switch except [PTT] is pushed, the

backlight lights for 5 seconds�

Contrast

Push to open the “Contrast” window� Then, push [Up]

or [Down] to select the LCD contrast level between 0

(the lowest) and 50 (the highest)�

Assignable Software key functions (Continued)

Содержание IC-F62D






























































































































Результаты поиска

Содержание IC-F62D

Отзывы:

Похожие инструкции для IC-F62D

Бренды по названию

Популярные бренды

Icom IC-F62D, Руководство по эксплуатации

Результаты поиска

Содержание IC-F62D

Отзывы:

Похожие инструкции для IC-F62D

Бренды по названию

Популярные бренды