Icom IC-2710H Скачать руководство пользователя страница 32

Страница: 32 / 88

REPEATER OPERATION

■

Operation

➀

Push the desired band’s tuning dial.

➁

Set the receive frequency (repeater output frequency).
(pgs. 15–19)

➂

Push and hold [DUP] to select – duplex or push it for 1 sec.
again for + duplex.

• “DUP –” or “DUP” appears to indicate the transmit frequency for

minus shift or plus shift, respectively.

• When the auto repeater function is turned ON, (available for the

U.S.A. version only), steps

➁

and

➂

are not necessary. (p. 31)

➃

Push and hold [

(DTMF)

T] to turn ON the subaudible tone

encoder, according to repeater requirements.

• Refer to p. 29 for tone frequency settings.
• When the repeater requires a different tone system, see the page

at right.

➄

Push and hold [PTT] to transmit.

• The displayed frequency automatically changes to the transmit

frequency (repeater input frequency).

• The operating condition is automatically programmed into a

scratch pad memory. See p. 39 for details.

• If “oFF” appears, confirm the offset frequency. (p. 30)

➅

Release [PTT] to receive.

➆

Push the selected band’s [MONI] to check whether the
other station’s transmit signal can be directly received or
not.

➇

To return to simplex, push [DUP] for 1 sec., once or twice,
to clear the “DUP” indicator.

➈

To turn OFF the subaudible tone encoder, push and hold
[

(DTMF)

T].

• “T” disappears.
• When the optional UT-104 is installed, push and hold [

(DTMF)

an additional 2 times (for a total of 3 times).

DUP –

IC-2710H.qxd 02.2.8 16:55 Page 27 (1,1)

Содержание IC-2710H

























































































Результаты поиска

Содержание IC-2710H

Отзывы:

Icom IC-2710H, Инструкция по эксплуатации, Страница: 32 / 88

Результаты поиска

Содержание IC-2710H

Отзывы: