Icom IC-2710H Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 88

Icom IC-2710H Скачать руководство пользователя страница 31

4

BASIC OPERATION

26

The microphone can select the desired output
power directly.

Ä

Push [BAND] to select the desired band, if nec-
essary.

Å

Push [

➃

HIGH] for high output power; [

➄

MID] for

middle output power; and [

➅

LOW] for low out-

put power.

• The output power CANNOT be changed while trans-

mitting.

■

Crossband full duplex

The transceiver can receive a signal on the sub band while
transmitting on the main band. Using this capability, cross-
band full duplex operation is possible. No special setting is
necessary for crossband full duplex operation.

➀

Set the desired transmit and receive frequencies on the
main and sub bands respectively for your transceiver.
(pgs. 15–19)

➁

Set the same frequencies, but set the receive band as the
main band for the other transceiver.

➂

Push and hold [PTT] to operate with full duplex.

• Transmitting and receiving activate simultaneously.
• One-touch PTT function (at right) and time-out timer are useful

for crossband full duplex operation. (p. 72)

■

One-touch PTT function

The PTT switch can be operated as a one-touch
PTT switch (each push toggles transmit/receive).
Using this function, you can transmit without push-
ing and holding the PTT switch.

To prevent accidental, continuous transmissions
with the one-touch PTT function, the transceiver
has a time-out timer. See p. 72 for details.

Ä

Push [FUNC] then [

➂

PTT-M] to turn the one-touch PTT

function ON.

• The activity indicator lights green.

Å

Push [PTT] to transmit and push again to receive.

• Two beeps sound when transmission is started and a long beep

sounds when returning to receive.

• “

$

” flashes while transmitting with the one-touch PTT func-

tion.

Ç

Push [FUNC] then [

➂

PTT-M] to turn the one-touch PTT

function OFF.

• The activity indicator goes out.

HIGH

4

MID

5

LOW

6

PTT-M

3

IC-2710H.qxd 02.2.8 16:55 Page 26 (1,1)

«
...
29
30
31
32
33
...
»

Содержание IC-2710H

























































































Отзывы:

Нет отзывов