icetro ID-0160-AN Скачать руководство пользователя страница 38

Страница: 38 / 46

Cleaning Procedure

In a large pitcher, mix 8oz of nickel safe, ice machine cleaner or sanitizer for every gallon of water.

PLEASE OBSERVE THE CLEANING SOLUTION MIXING RATIO. FAILURE TO DO SO MAY RESULT IN
CHEMICAL DAMAGE TO THE MACHINE.

Preparation for Washing and Disinfection -

Power switch set to ‘ON’ and operation switch set to ‘OFF’

Dispense Ice

●

Press the ICE &

WATER buttons

simultaneously for

3 seconds until

both light up.

●

Place a cup/bucket

under ice chute

and press

dispensing lever to

discharge ice until

hopper is empty.

●

Press the

DOWN & SET

buttons

simultaneously

for 3 seconds.

Machine will

enter the

FORCED DRAIN

feature for 30

seconds.

Note:

Ice machine cleaners are used to remove mineral deposits such as lime marks. It cannot be used to remove scale or

sticky mucus. It is recommended to proceed with cleaning first and then to sanitize. Do not mix chemicals together,

doing so is

VERY

dangerous!

Содержание ID-0160-AN















































Результаты поиска

Содержание ID-0160-AN

Отзывы:

Похожие инструкции для ID-0160-AN

Бренды по названию

Популярные бренды

icetro ID-0160-AN, Инструкция по установке и обслуживанию

Результаты поиска

Содержание ID-0160-AN

Отзывы:

Похожие инструкции для ID-0160-AN

Бренды по названию

Популярные бренды