Ice 18ZR Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 86

background image

Section 6: MAINTENANCE Page 4

0

OM-ZR-May15

Grease Clamp Plungers

Grease the plunger in the with any good
multi-purpose grease (2-3 pumps) at least once
a day. If submerging the clamp in water or
mud, grease plunger frequently to push out
foreign matter. Dusty conditions also require
frequent greasing.

Grease fitting

Grease fitting

Power Unit Pump Drive Adapter

The pump drive adapter from factory is filled with Schaeffer 268 synthetic gear oil and is the preferable lubri-
cant. Schaeffer 740 or 741 are acceptable replacements, as well as the alternates in the table. More frequent
service is recommended if these alternate lubricants are used.

Engine oil

CAT CH-4 (10W-30)

Vibratory gear case

Schaeffer 740/741 ISO 220/150

Pump drive adapter

Schaeffer 268, ISO 320

Gear Case Oil Lube Pump

The hoses on the gear case lube
pump hoses should be bled when
first placed in operation to ascertain
proper function and to purge air from
system. The filter should be checked
and cleaned when servicing gear oil.
Be aware of foreign material in filter
and have oil tested if in doubt. A
periodic oil testing program is
encouraged. Make sure all hoses are
in good condition, not routed tight the
vibrator’s edges and fittings are tight.

Lube Pump

Lube Pump
Filter

Factory Installed Oils

Drain Plug

«
...
40
41
42
43
44
...
»

Содержание 18ZR























































































Отзывы:

Нет отзывов

Похожие инструкции для 18ZR

Бренд: Balmar Страницы: 20

Бренд: Ibiza sound Страницы: 28

Бренд: LENCO Страницы: 52

Бренд: MULTIQUIP Страницы: 4

ElectroMate VEC095

Бренд: Vector Страницы: 20

Бренд: Denver Страницы: 15

Бренд: Hayter Страницы: 52

Бренд: Koss Страницы: 2

Бренд: Chinavision Страницы: 8

Бренд: Action Страницы: 47

Бренд: Titan Страницы: 24

Бренд: Cosman Страницы: 115

Бренд: Malektronic Страницы: 6

Бренд: Audiovox Страницы: 34

Energy Radio 150

Бренд: ENERGY SISTEM Страницы: 40

MG3700A MG3700A

Бренд: Anritsu Страницы: 268

Бренд: Anritsu Страницы: 317

Бренд: CMX Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды