manualshive.com logo in svg

Ice 18ZR, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Ice 18ZR Скачать руководство пользователя страница 27

Section 5: OPERATION                                                                                Page 25                                                                                             

OM-ZR-

 

May15

Complete all preparation as described in Section 4: PREPARATION FOR OPERATION. 

Read Section 6: MAINTENANCE and perform any required maintenance.  See Caterpillar Operation &
 Maintenance Manual

. 

Completion of Set-up and Maintenance 

Control Panel Components 

The power unit control panel contains the controls for the diesel engine and displays operating parameters and 
fault lights.  Local controls are provided for the vibrator and clamp.  A remote-control pendant is provided as the 
primary control for vibrator and clamp. 

The control panel and pendant contain following controls and components: 

The OPERATION AND MAINTENANCE INSTRUCTIONS near the control panel are there as reminders only.  They 
are not intended to substitute for a thorough understanding of this Operation Manual. 

Number

 

Description

 

1 

Main circuit pressure gauge 

2 

Clamp circuit pressure gauge 

3 

Hydraulic oil temperature gauge/switch 

4 

Return filter pressure gauge 

5 

Emergency stop button 

6 Hour 

meter 

7 

Engine power switch (OFF-ON-START) 

8 

Engine speed switch (SLOW-FAST) 

9 

Remote - Local switch (REMOTE-LOCAL) 

10 

Main circuit (vibro motors) switch (REV-OFF-FOR) 

11 

Clamp switch (OPEN-CLOSE) 

12 

Clamp light (CLOSED) 

13 

Moment actuator switch - ZR function (DEC-INC)  

14 

Service engine light  

15 

Hydraulic oil temperature low light 

16 

Hydraulic oil temperature high light 

17 

Hydraulic oil level low light 

18 

Return filter clog light 

19 

Emergency stop light 

20 Engine 

display 

 

21 

Pendant override switch (PO) (inside control panel) 

22 

Maintenance reset switch (MR) (inside control panel) 

23 

Hydraulic override switch (HO) (inside control panel) 

24 

Pendant EMERGENCY STOP button 

25 

Pendant clamp light (CLOSED) 

26 

Pendant clamp switch (OPEN-CLOSE) 

27 

Pendant moment actuator switch - ZR function (DEC-INC)  

28 

Pendant main circuit switch (REV-OFF-FOR) 

29 

Pendant engine speed switch (SLOW-FAST)  

30 

Moment actuator pressure gauges - ZR function 

31 

Lube Pressure Light (Yellow)-ZR Vibrator 

Содержание 18ZR























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды