background image

6. Locate blue float valve on/off lever. Move lever
up about half way to shut water off.

7. Locate drain plug and pull the drain plug out to
drain the reservoir and evaporator. When draining
is complete, return the plug to its original position.

8. Obtain pre-mixed Ice-O-Matic Clear 1 Scale
remover solution (with squirt bottle) or mix a
solution of Clear 1 with water: 2.5 ounces of Clear
1 with 1 quart (32 oz) of warm water.

Note: Take care not to spill any scale remover on
any nearby surface. Immediately wipe any spill with
baking soda and water.

9. Fill the 16 oz squirt bottle with the diluted scale
remover.

10. Fill the reservoir with the scale remover solution
using squirt bottle or other container. That will be
about 8 ounces or half a squirt bottle.

Page 13

GEMU090
Installation and Use

Ice

Making

Check
Water

Time to

Clean

Clean
Reset

Fill Reservoir Using Squirt Bottle

Ice machine scale
remover contains acids.
Acids can cause burns.

If concentrated cleaner
comes in contact with
skin, flush with water. If
swallowed, do NOT
induce vomiting. Give
large amounts of water
or milk. Call Physician
immediately. Keep out
of the reach of children.

Ice

Making

Check
Water

Time to

Clean

Clean
Reset

Drain Plug

Ice

Making

Check
Water

Time to

Clean

Clean
Reset

Drain Plug

Содержание GEMU090 Series

















Отзывы: