Ice-O-Matic GEMU090 Series Скачать руководство пользователя страница 12

Use

No special instructions are needed for use. Just
take as much ice as you need, the machine will
replace it. A scoop is provided, and it can be stored
in the machine using the loop of tubing on the right
side as a holder.

The machine can be shut off anytime by just
pushing and releasing the On/Off button.

What shouldn’t be done?

Never keep anything in the ice storage bin that is
not ice. Objects like wine or beer bottles are not
only unsanitary, but the labels can slip off and plug
up the drain.

Never allow the machine to operate without regular
cleaning. The machine will last longer if it is kept
clean. Regular cleaning should happen at least
once per year, and preferably twice. Some water
conditions will dictate even more frequent cleaning
of the ice making section, and some carpets or
pets will dictate more frequent cleaning of the
condenser.

Note: The Time to Clean light will switch ON after 6
months of use. It will remain ON until the ice
making system is cleaned using the process on
page 14.

Noise:

The ice machine is designed for quiet operation,
but will make some noise during the ice making
cycle.

Ice Making

During ice making, pearl ice will drop into the bin at
an irregular rate; sometimes there will be little ice
falling while at other times a group of pearls will fall.
Some water drops may also come out with the ice.
Both conditions are normal.

Page 10

GEMU090
Installation and Use

Control Panel

On/Off Control Button

Clean Button

Glows Green when

unit is switched On

Glows Yellow when
it's time to clean the
machine

Glows Red when there is no water

supplied to the machine

The machine will NOT make ice

when this light is on. It will restart

and the light will go out when the

water supply is restored.

Содержание GEMU090 Series

















Отзывы: