ICE COBOTICS i-Synergy RS28L-CY, Руководство оператора

Страница: 10 / 45

10 ICE RS28L-CY
OPERATOR MANUAL
TANK DRAINING
4. If the squeegee assembly leaves streaks on the
floor, raise the squeegee off the floor and wipe
the blades down with a damp cloth. Pre-sweep
the area to prevent leaving streaks on the floor.
5. To obtain the optimum cleaning performance,
you can adjust the brush pressure, solution
flow and detergent dosage as your required. If
poor picking up water performance is observed,
please stop scrubbing and check the squeegee
blade, adjust or replace if necessary.
6. If the dirty water path exceed the width of
squeegee, please adjust the side squeegee
assembly.
7. Pour a recommended defoamer into the
recovery tank if excessive foam appears.
WARNING: The foam do not activate
water level switch, excessive foam may result
in vacuum motor damage.
8. Press the Horn button (Machine components,
#27) to alert if necessary.
9. The machine is equipped with a Warning light
(Machine components, #21), you can select turn
ON or OFF by the Warning light button (Machine
components, #40).
10. If there have Fault icon display and blinking
on the touch screen, please stop using the
machine and to eliminate the fault (Please see
FAULT CODES AND ELIMINATE section).
11. For heavily soiled areas, please use HEAVY
DUTY SCRUBBING mode by work mode select
button.
12. If you only want to pick up water needn't
scrubbing, Turn on the Vacuum motor
button(Machine components, #38) , the
squeegee will lower down, and turn off the
1-Step starting button (if it is ON), the scrub
head will raise and then start to picking water
up.
DRAINING THE RECOVERY TANK
Any time scrubbing is completed, or when refilling
solution tank, the recovery tank should be drained
and cleaned.
WARNING: If the recovery tank is not
drained when the solution tank has been
refilled, foam or water may enter the float shut-
off screen and cause damage to the vacuum
motor.
1. While holding the Recovery tank drain hose
(Machine components, #41) upward, remove
the cap and lower hose to drain.
2. Open the Recovery tank cover (Machine
components, #22) and rinse out the tank. Use
a rag to remove any excess dirt.
3. Remove and clean the vacuum fan inlet filter
located in the recovery tank. Clean the filter with
a damp cloth or low pressure water hose if dirty.
Allow the vacuum fan filter to dry completely
before reinstalling it in the machine.
DRAINING THE SOLUTION TANK
Any time scrubbing operation is completed, the
solution tank should be drained and cleaned.
1. While holding the Solution tank drain hose
(Machine components, #43) upward, remove
the cap and lower hose to drain.
2. Rinse the solution tank with clean water after
every use. This will help prevent chemical
buildup and clogging of the solution lines.
WARNING: Fire or Explosion Hazard.
Keep Sparks and Open Flame Away. Keep
Battery Compartment Propped Open When
Charging.
Use only ICE supplied or approved batteries
charger, use unapproved charger may cause
damage to the batteries and machine.
Batteries charger specifications:
• Applicable to charging Lithium-ion batteries
• Automatic shut off circuit
• Output current of 30 Amps
• Output voltage of 24 volts
1. Transport the machine to a well ventilated area.
2. Turn the machine off.
3. Prop up the Operator seat by the support stand
for ventilation.
4. Connect the charger's AC power supply cord to
a properly grounded receptable.
5. The charger will automatically begin to charge,
you can watching the charging status on the
window (Machine components, #20), once the
charging cycle begins, the indicator lights will
progress from red, yellow to green. when the
green indicator light comes on, the charging
cycle is done. Unplug the charger cord.
NOTE: The machine will can not operate
when charging.
BATTERY CHARGING