IC Realtime DVR704MSGV5 Скачать руководство пользователя

Страница: 27 / 144

The video signal should comply with your national standards.

The input video signal shall have high SNR, low distortion; low interference, natural color and

suitable lightness.

Guarantee the stability and reliability of the camera signal:

The camera shall be installed in a cool, dry place away from direct sunlight, inflammable,

explosive substances and etc.

The camera and the DVR should have the same grounding to ensure the normal operation of the

camera.

Guarantee stability and reliability of the transmission line

BTT TB

Please use high quality, sound shielded BNC. Please select suitable BNC model according to the

transmission distance.

If the distance is too long, you should use twisted pair cable, and you can add video compensation

devices or use optical fiber to ensure video quality.

You should keep the video signal away from the strong electromagnetic interference, especially

the high tension current.

Keep connection lugs in well contact

BTTTB

The signal line and shielded wire should be fixed firmly and in well connection. Avoid dry joint, lap

welding and oxidation.

BT TTB

3.5.2

Audio Input

Due to high impedance of audio input, please use active sound pick-up.

Audio transmission is similar to video transmission. Try to avoid interference, dry joint, loose

contact and it shall be away from high tension current.

3.5.3

Audio/Video Input Switch Cable

Please use the following audio/video input cable if your camera port is BNC.

Please refer to Figure 3-5 for 4-pin aviation port cable information.

Figure 3-5

Please refer to the following sheet for detailed information.

Socket

Switch

cable

color

and

definition

Port

4-pin aviation port

DC power male socket. External is

negative and internal is positive.

（

Camera power

）

12V external camera power

DC power male socket. External is

GND

Содержание DVR704MSGV5

















































































































































Результаты поиска

Содержание DVR704MSGV5

Отзывы:

Похожие инструкции для DVR704MSGV5

Бренды по названию

Популярные бренды

IC Realtime DVR704MSGV5, Руководство пользователя

Результаты поиска

Содержание DVR704MSGV5

Отзывы:

Похожие инструкции для DVR704MSGV5

Бренды по названию

Популярные бренды