IC Realtime DVR704MSGV5 Скачать руководство пользователя

Страница: 30 / 144

Figure 3-7

Please refer to the following sheet for detailed information.

Name

Pin Introduction

～

Alarm input 1

～

Alarm input 7

Alarm GND

9/11

NC1/NC2 of alarm output 1/2

10/12

NO1/NO2 of alarm output 1/2

3.7.2

Alarm Input Port

Please refer to the following sheet for more information. See Figure 3-8.



Normal open or Normal close type.



Please parallel connect COM end and COM end of the alarm detector (Provide external

power to the alarm detector).



Please parallel connect the Ground of the DVR and the ground of the alarm detector.



Please connect the NC port of the alarm sensor to the DVR alarm input(ALARM)



Use the same ground with that of DVR if you use external power to the alarm device.

Figure 3-8

3.7.3

Alarm Output Port



Alarm output 1/2 is level input, output voltage is 12V. The max load shall be less than 12V/1A.

It should not be connected to high power load directly to avoid high current which may result

in relay damage. Please use the co contactor to realize the connection between the al arm

output port and the load.



To avoid overloading, please read the following relay parameters sheet carefully.

Relay Specification

Содержание DVR704MSGV5

















































































































































Результаты поиска

Содержание DVR704MSGV5

Отзывы:

Похожие инструкции для DVR704MSGV5

Бренды по названию

Популярные бренды

IC Realtime DVR704MSGV5, Руководство пользователя

Результаты поиска

Содержание DVR704MSGV5

Отзывы:

Похожие инструкции для DVR704MSGV5

Бренды по названию

Популярные бренды