IC Realtime DVR704MSGV5 Скачать руководство пользователя

Страница: 141 / 144

133

There are following possibilities:



Alarm setup is not correct.



Alarm output has been open manually.



Input device error or connection is not correct.



Some program versions may have this problem. Please upgrade your system.

17. Alarm function is null.

There are following possibilities:



Alarm setup is not correct.



Alarm cable connection is not correct.



Alarm input signal is not correct.



There are two loops connect to one alarm device.

18. Remote control does not work.

There are following possibilities:



Remote control address is not correct.



Distance is too far or control angle is too small.



Remote control battery power is low.



Remote control is damaged or DVR front panel is damaged.

19. Record storage period is not enough.

There are following possibilities:



Camera quality is too low. Lens is dirty. Camera is installed against the light. Camera

aperture setup is not correct.



HDD capacity is not enough.



HDD is damaged.

20. Can not detect SIM card

There are following possibilities:



There is no SIM card.



SIM card direction is wrong.



SIM card is malfunction.

21. My cell phone 3G dial failed.

There are following possibilities:



You have not installed the dial module or your installation is not right.



Please make sure you have inserted the card.



You have not installed the antenna or the connection is not sound.



The centre platform configuration is not right or the registration is not effective.



The cell phone remaining sum is not sufficient.



Signal is too weak.



SIM card does not support corresponding service.

22. 3G platform is offline

There are following possibilities:



Refer to the above item to check 3G dial function is OK or not.

Содержание DVR704MSGV5

















































































































































Результаты поиска

Содержание DVR704MSGV5

Отзывы:

Похожие инструкции для DVR704MSGV5

Бренды по названию

Популярные бренды

IC Realtime DVR704MSGV5, Руководство пользователя

Результаты поиска

Содержание DVR704MSGV5

Отзывы:

Похожие инструкции для DVR704MSGV5

Бренды по названию

Популярные бренды