IBM J58S Скачать руководство пользователя | Manualshive

Страница: 1 / 28

background image

IBM Ethernet Appliance J58S
Getting Started Guide

April 2010
Part Number:

This document describes how to install the IBM Ethernet Appliance J58S.

Contents

About This Guide .............................................................................................3
Step 1: Prepare the Site ...................................................................................4

Rack-Mounting Requirements ...................................................................4
Required Tools ..........................................................................................5

Step 2: Install the Mounting Hardware ............................................................6

Install the Mounting Hardware in a Four-Post Rack or Cabinet .................6
Install the Mounting Hardware in an Open-Frame Rack ............................7

Step 3: Install the Device .................................................................................8

Install the Device Using a Lift ....................................................................9
Install the Device Without a Mechanical Lift ...........................................10

Remove Components .......................................................................11
Lift the Chassis into the Rack ............................................................12
Reinstall Components ......................................................................13

Step 4: Connect External Devices and IOC Cables .........................................13

Connect to a Network for Out-of-Band Management ...............................14
Connect a Management Console .............................................................14
Connect the IOC Cables ..........................................................................14

Step 5: Connect Ground and Power Cables ...................................................15

Connect the Grounding Cable .................................................................15
Connect Power to an AC-Powered Ethernet Appliance ............................16
Connect Power to a DC-Powered Ethernet Appliance .............................17

Step 6: Perform Initial Software Configuration ..............................................19
Safety Warnings ............................................................................................24
Compliance Statements for NEBS ..................................................................25

■

1

1
2
3
...
»

Содержание J58S





























Отзывы:

Нет отзывов

Похожие инструкции для J58S

Бренд: Data Translation Страницы: 60

Бренд: Patton electronics Страницы: 51

Бренд: iBall Baton Страницы: 9

RUGGEDMAX WIN7000

Бренд: RuggedCom Страницы: 42

RS-232/422/485 Serial Card CE 3PXCC4A

Бренд: B&B Electronics Страницы: 47

Бренд: Buffalo Страницы: 2

Бренд: Maipu Страницы: 80

DataPlot CB1224

Бренд: B-G Instruments Страницы: 4

Бренд: Lanner Страницы: 38

Бренд: Allied Telesis Страницы: 34

Бренд: Patton electronics Страницы: 2

CyberSWITCH CSX101

Бренд: Cabletron Systems Страницы: 72

Бренд: B+B SmartWorx Страницы: 50

Бренд: Cradlepoint Страницы: 2

Бренд: SilverStone Страницы: 28

netHOST NHST-T100

Бренд: hilscher Страницы: 75

Бренд: RR-Concepts Страницы: 12

Бренд: Omron Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды