IBM FC EJ05 Скачать руководство пользователя страница 50

Страница: 50 / 66

Table 2. Situations and steps for preparing the client logical partitions (continued)
Situation

Steps

HMC-managed systems only: You have redundant

Virtual I/O Server logical partitions that, in

conjunction with virtual client adapters, provide

multiple physical volumes that are used to mirror a

volume group.

See the procedures for your client operating

system. For example, for AIX, see Replacing a disk

on the Virtual I/O Server in the Advanced POWER

Virtualization Best Practices Redpaper. The

procedure for Linux is similar to this procedure for

AIX.For example, for AIX, see Replacing a disk on

the Virtual I/O Server in the Advanced POWER

Virtualization Best Practices Redpaper. The

procedure for Linux is similar to this procedure for

AIX.

You do not have redundant Virtual I/O Server

logical partitions.

Shut down the client logical partition.
For systems that are managed by the HMC, see

Stopping a system (www.ibm.com/support/

knowledgecenter/POWER9/p9haj/

stopsyshmc.htm).

Verifying that the hot-plug PCI tools are installed for Linux

Find information about using the hot-plug PCI tools for a PCI adapter installed in a system with a Linux

operating system.

Procedure

1. Enter the following command to verify that the hot-plug PCI tools are installed:

rpm -aq | grep

powerpc-utils

If the command does not list any

powerpc-utils

packages, the PCI Hot Plug tools are not installed.

2. Enter the following command to ensure that the rpaphp driver is loaded:

ls -l /sys/bus/pci/

slots/

The directory should contain data.
• If the directory is empty, the driver is not loaded or the system does not contain hot-plug PCI slots.

The following is an example of the information displayed by this command:

drwxr-xr-x 15 root root 0 Feb 16 23:31 .

drwxr-xr-x 5 root root 0 Feb 16 23:31 ..

drwxr-xr-x 2 root root 0 Feb 16 23:31 0000:00:02.0

drwxr-xr-x 2 root root 0 Feb 16 23:31 0000:00:02.2

drwxr-xr-x 2 root root 0 Feb 16 23:31 0000:00:02.4

drwxr-xr-x 2 root root 0 Feb 16 23:31 0001:00:02.0

drwxr-xr-x 2 root root 0 Feb 16 23:31 0001:00:02.2

drwxr-xr-x 2 root root 0 Feb 16 23:31 0001:00:02.4

drwxr-xr-x 2 root root 0 Feb 16 23:31 0001:00:02.6

drwxr-xr-x 2 root root 0 Feb 16 23:31 0002:00:02.0

drwxr-xr-x 2 root root 0 Feb 16 23:31 0002:00:02.2

drwxr-xr-x 2 root root 0 Feb 16 23:31 0002:00:02.4

drwxr-xr-x 2 root root 0 Feb 16 23:31 0002:00:02.6

• If the directory does not exist, run the following command to mount the filesystem:

mount -t

sysfs sysfs /sys

3. Ensure the following tools are available in the

/usr/sbin

directory.

• lsslot
• drmgr -c pci

4. Return to the procedure that sent you here.

36 Power Systems: PCIe adapters for the 9080-M9S

Содержание FC EJ05



































































Результаты поиска

Содержание FC EJ05

Отзывы:

Похожие инструкции для FC EJ05

Бренды по названию

Популярные бренды

IBM FC EJ05, Руководство пользователя

Результаты поиска

Содержание FC EJ05

Отзывы:

Похожие инструкции для FC EJ05

Бренды по названию

Популярные бренды