IBM FC EJ05 Скачать руководство пользователя страница 44

Страница: 44 / 66

2. At the command line, type

smitty

3. Select Devices.
4. Select PCI Hot Plug Manager and press Enter.

The PCI Hot-Plug Manager menu displays.
For details about the menu options in the PCI Hot-Plug Manager screen, see “PCI hot-plug manager

menu” on page 30.

What to do next
Return to the procedure that directed you here.

PCI hot-plug manager menu

Find information about how to use the PCI Hot Plug Manager to service PCI adapters with the system

power on in AIX. The following options are available from the PCI Hot Plug Manager menu.
Note: For information about the PCI slot LED states, see “Component LEDs” on page 31.

Table 1. PCI Hot Plug Manager menu options
Menu option

Description

List PCI hot-plug

slots

Provides a descriptive list of all slots that support PCI hot-plug capability. If the

listing for a slot indicates it holds an unknown device, select the Install/configure

Devices added after IPL to configure the adapter in that slot.

Add a PCI hot-

plug adapter

Allows the user to add a new PCI hot-plug-capable adapter to the slot with the

system turned on. You will be asked to identify the PCI slot that you have selected

prior to the actual operation. The selected PCI slot will go into the Action state and

finally into the On state.
Note: The system will indicate the slot holds an unknown device until you perform

the Install/configure devices added after IPL option to configure the adapter.

Replace/remove

a PCI hot-plug

adapter

Allows the user to remove an existing adapter, or replace an existing adapter with an

identical one. For this option to work, the adapter must be in the Defined state (see

the "Unconfigure a Device" option). You will be asked to identify the PCI slot prior to

the actual operation. The selected PCI slot will go into the Action state.

Identify a PCI

hot-plug slot

Allows the user to identify a PCI slot. The selected PCI slot will go into the Identify

state. See “Component LEDs” on page 31.

Unconfigure a

device

Allows the user to put an existing PCI adapter into the Defined state if the device is

no longer in use.
This step must be completed successfully before starting any removal or

replacement operation. If this step fails, the customer must take action to release

the device.

Configure a

defined device

Allows a new PCI adapter to be configured into the system if software support is

already available for the adapter. The selected PCI slot will go into the On state.

Install/configure

devices added

after IPL

The system attempts to configure any new devices and tries to find and install any

required software from a user-selected source.

The add, remove, and replace functions return information to the user indicating whether the operation

was successful. If additional instructions are provided on the screen, complete the recommended

actions. If the instructions do not resolve the problem, do the following:
• If the adapter is listed as Unknown, perform the Install/configure devices Added After IPL option to

configure the adapter.

30 Power Systems: PCIe adapters for the 9080-M9S

Содержание FC EJ05



































































Результаты поиска

Содержание FC EJ05

Отзывы:

Похожие инструкции для FC EJ05

Бренды по названию

Популярные бренды

IBM FC EJ05, Руководство пользователя

Результаты поиска

Содержание FC EJ05

Отзывы:

Похожие инструкции для FC EJ05

Бренды по названию

Популярные бренды