IBM E850C, Технический обзор и введение

Страница: 34 / 160

20
IBM Power System E850C: Technical Overview and Introduction
Feature #7109
Intelligent PDU with Universal UTG0247 Connector is for an intelligent ac power distribution
unit (PDU+) that allows the user to monitor the amount of power being used by the devices
that are plugged in to this PDU+. This ac power distribution unit provides 12 C13 power
outlets. It receives power through a UTG0247 connector. It can be used for many different
countries and applications by varying the PDU to Wall Power Cord, which must be ordered
separately. Each PDU requires one PDU to Wall Power Cord. Supported power cords include
the following features: 6489, 6491, 6492, 6653, 6654, 6655, 6656, 6657, and 6658.
Feature #7188
Power Distribution Unit mounts in a 19-inch rack and provides 12 C13 power outlets. Feature
7188 has six 16A circuit breakers, with two power outlets per circuit breaker. System units
and expansion units must use a power cord with a C14 plug to connect to the feature 7188.
One of the following power cords must be used to distribute power from a wall outlet to the
feature 7188: feature 6489, 6491, 6492, 6653, 6654, 6655, 6656, 6657, or 6658.
Feature #EPTJ
This feature is an intelligent, switched 200 - 240 volt ac PDU with nine C19 receptacles on the
front of the PDU. The PDU is mounted on the rear of the rack, making the nine C19
receptacles easily accessible. Each receptacle has a 20 amp circuit breaker. Depending on
country wiring standards, the PDU is single-phase or three-phase wye. See three-phase
feature #EPTK or #EPTL for countries that do not use wye wiring. The PDU can be mounted
vertically in rack side pockets, or it can be mounted horizontally. If mounted horizontally, it
uses 1 EIA (1U) of rack space. See feature #EPTH for horizontal mounting hardware. Device
power cords with a C20 plug connect to C19 PDU receptacles and are ordered separately.
One country-specific wall power cord is also ordered separately and attaches to a UTG524-7
connector on the front of the PDU.
Supported power cords include features #6489, #6491, #6492, #6653, #6654, #6655, #6656,
#6657, #6658, and #6667.
Feature #EPTL
This feature is an intelligent, switched 208 volt 3-phase ac PDU with nine C19 receptacles on
the front of the PDU. The PDU is mounted on the rear of the rack, making the nine C19
receptacles easily accessible. Each receptacle has a 20 amp circuit breaker. The PDU can be
mounted vertically in rack side pockets, or it can be mounted horizontally. If mounted
horizontally, it uses 1 EIA (1U) of rack space. See feature #EPTH for horizontal mounting
hardware. Device power cords with a C20 plug connect to C19 PDU receptacles and are
ordered separately. One wall power cord is provided with the PDU (no separate feature
number) and has an IEC60309 60A plug (3P+G). The PDU supports up to 48 amps. Two
RJ45 ports on the front of the PDU enable the client to monitor each receptacle’s electrical
power usage and to remotely switch any receptacle on or off. The PDU is shipped with a
generic PDU password. IBM strongly urges clients to change it upon installation.
Feature #EPTN
This feature is an intelligent, switched 200 - 240 volt ac PDU with twelve C13 receptacles on
the front of the PDU. The PDU is mounted on the rear of the rack, making the twelve C13
receptacles easily accessible. Each receptacle has a 20 amp circuit breaker. Depending on
country wiring standards, the PDU is single-phase or three-phase wye. See three-phase
feature #EPTK or #EPTL for countries that do not use wye wiring. The PDU can be mounted
vertically in rack side pockets, or it can be mounted horizontally. If mounted horizontally, it
uses 1 EIA (1U) of rack space. See feature #EPTH for horizontal mounting hardware. Device
power cords with a C14 plug connect to C13 PDU receptacles and are ordered separately.