IBM B50 Скачать руководство пользователя

Страница: 151 / 198

Power Supply

DANGER

Do not attempt to open the covers of the power supply. Power supplies
are not servicable and are to be replaced as a unit.

Removal

1. Remove the cover as described in “Removing the Cover” on page 7-3.

2. Remove the riser card support bracket, as described in “Riser Card Support

Bracket” on page 7-10.

3. Disconnect the power supply cables from the system board connectors and any

installed drives. Label each cable, identifying where it connects.

4. Remove the mounting screws from the rear of the power supply.

5. Remove the power supply from the system by moving it forward and then

upward, as shown in the following illustration:

Replacement

Replace in reverse order, noting the following power supply cable attachments.

System board power cables

Diskette drive power cable

Disk drive power cables

Media drive power cables

Chapter 7. Removal and Replacement Procedures

7-7

Содержание B50







































































































































































































Результаты поиска

Содержание B50

Отзывы:

Похожие инструкции для B50

Бренды по названию

Популярные бренды

IBM B50, Руководство по обслуживанию

Результаты поиска

Содержание B50

Отзывы:

Похожие инструкции для B50

Бренды по названию

Популярные бренды