IBM AS/400e Скачать руководство пользователя страница 44

Страница: 44 / 85

Replacing the covers on your AS/400e system 620 or server S20

__ 1.

Install the access cover and secure with slotted-head screws.

__ 2.

Install the side cover for the system unit as follows:

Install the side cover. The cover may fall if you do not hold on to it.

Secure with the two screws.

Slide the cover latches down to close the louvers.

__ 3.

Install the top cover by sliding it towards the back of the system.

__ 4.

Secure the screw and pivot the top cover lock.

__ 5.

While gripping its upper corners, install the back cover.

__ 6.

Install the AS/400 front cover by doing the following:

Install the cover

Figure 32. Installing optical cables in a system 620 or server S20

Setting Up Your 5065 or 5066 Expansion Unit V4R5

Содержание AS/400e






















































































Результаты поиска

Содержание AS/400e

Отзывы:

Похожие инструкции для AS/400e

Бренды по названию

Популярные бренды

IBM AS/400e, Руководство пользователя

Результаты поиска

Содержание AS/400e

Отзывы:

Похожие инструкции для AS/400e

Бренды по названию

Популярные бренды