background image

Statement 8:

CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.

Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect a problem with one of these parts, contact
a service technician.

Statement 10:

CAUTION:
Do not place any object weighing more than 82 kg (180 lb) on top of
rack-mounted devices.

>82 kg (180 lb)

WARNING:

Handling the cord on this product or cords associated with accessories

sold with this product, will expose you to lead, a chemical known to the State of
California to cause cancer, and birth defects or other reproductive harm.

Wash

hands after handling.

ADVERTENCIA:

El contacto con el cable de este producto o con cables de

accesorios que se venden junto con este producto, pueden exponerle al plomo, un
elemento químico que en el estado de California de los Estados Unidos está
considerado como un causante de cancer y de defectos congénitos, además de
otros riesgos reproductivos.

Lávese las manos después de usar el producto.

Safety

xi

Содержание 8835 - Eserver 325 - 1 GB RAM































































Отзывы: