iBell Tools MS06-16 Скачать руководство пользователя

Страница: 18 / 19

Suspected malfunctions are often due to causes that the users can
fix themselves, therefore check the product using this section. In
most cases the problem can be solved quickly.

Problem

Possible Cause

Solution

1. Product does
not start

1.1 Battery discharged
1.2 Battery damaged

1.3 Other electrical
defect to the product

1.1 Charge battery
1.2 Check by a
specialist electrician
1.3 Check by a
specialist electrician

2. Product does
not reach full
power

2.1 Battery capacity
too low

2.1 Charge battery

3. Unsatisfactory
result

3.1 Driver bit is worn
3.2 Driver bit not
suitable for intended
operation

3.1 Replace with a new
one
3.2 Use suitable driver
bit

TROUBLESHOOTING

WARNING!

Only perform the steps described within these

instructions! All further inspection, maintenance and repair work must

be performed by an authorised service centre or a similarly qualified
specialist if you cannot solve the problem yourself!

IBL MS06-16

Содержание MS06-16




















Результаты поиска

Содержание MS06-16

Отзывы:

Похожие инструкции для MS06-16

Бренды по названию

Популярные бренды

iBell Tools MS06-16, Руководство оператора

Результаты поиска

Содержание MS06-16

Отзывы:

Похожие инструкции для MS06-16

Бренды по названию

Популярные бренды