background image

3

Reflection film installation 
Please Note: TE-HUD project

s

 the display information on the

 

car

's windshield

, because the 

windshield

 is double

 pane

it

 will 

cause a

 

double image on the 

windshield

 when display

ed

.

  

If you can see  the

display information

 clearly

, then there  is no need to use the reflection 

film. If there is a double image, then please use the reflection film. 

First, please put the supplied non-slip mats in front of the dashboard, 
and then put the TE-HUD on it. 
Second, please stick the reflection film on the 

windshield

The reflecting film should be 

placed

 right above the host machine and it 

should be able to reflect the whole display screen. 

Methods of 

placing

 the film: 

1.

Clean

 the place that the film will be 

placed

 on 

with a lint free

 towel;

then mist the location with water.

2.

Tear off the back side

 (marked

 1

)

 of reflection film, then 

place

 it to the 

location

.

3.

After you have adjusted the location well, you can use a flat

 edge

 to 

slick the film and squeeze the water out until there

 

is no bubble or water 

in it.

4.

Tear off the front side (marked 2) of the reflection film. If the film 

cannot

 

display the whole information, please adjust the non-slip mat.

The first use of TE-HUD 
Start engine and power on TE-HUD, showing the current vehicle voltage 
and then 

begins

 to search ECU state, if the TE-HUD shows speed, 

rotating speed, indicating that TE-HUD has been installed successfully. 
(After 1 minute, if only display the voltage, please check whether TE-
HUD, OBD interface, and OBD data cable are correct

ly

 connect

ed

 and

 

the cable plug is fully seated into the 

vehicle OBD interface. 

Then restart the engine and TE-HUD will rescan.

TE-HUD setting 
TE-HUD display information is from ECU, 

if

 there is a difference

 

between vehicle dashboard and 

TE-HUD

, then you can enter the setup 

mode to fine-tune the TE-HUD display value, in order to achiev

e an 

exact match.

Содержание TE-HUD













Отзывы: