IBCcontrol F21050304 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 32

background image

MANUFACTURER'S DECLARATION

Manufacturer

IBC control AB
Brännerigatan 5 A, SE-263 37 Höganäs, Sweden

Product

Control unit for rotating heat exchanger

Type designation

VariMax50M

EU Directive

applicable to the

product

The manufacturer's declaration of conformity with the requirements of the
EMC Directive 2004/108/EC.

All control units are approved according to the requirements of the EMC
Directive 2004/108/EC and are tested according to standard
EN 61800-3:2004, emission category C1 and immunity category C2.

All control units comply with the Low Voltage Directive 2006/95/EC,
standard EN 61800-5-1.

All control units are designed for installation in environments subject to
pollution degree 2.

UL/CSA ETL 4009131.
All control units are also approved in accordance with UL 508C and CSA C22.2
No. 14.
Associated VariMax motor50 is approved in accordance with UL 1004-1,
UL 1004-3 and CSA C22.2 No. 100.

This product also complies with the RoHS Directive 2011/65/EU

including Commission Delegated Directive EU 2015/863.

Höganäs 2019-05-10

IBC control AB

Christer Persson
MD

-----------------------------------------------------------------------------------------

The FreeRTOS v6.1.0 (http://www.freertos.org) software is used in this
product and this source code can be supplied by us.

4

«
...
4
5
6
7
8
...
»

Содержание F21050304

































Отзывы:

Нет отзывов

Похожие инструкции для F21050304

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: Parker Страницы: 12

UNDER CONTROL CP-30A PILOT

Бренд: G-Force Страницы: 2

Бренд: Ashly Страницы: 1

Бренд: OneFex Страницы: 24

Бренд: Lampert Страницы: 15

Бренд: Sherlotronics Страницы: 2

Бренд: Viva Страницы: 9

Бренд: FMS Страницы: 9

Бренд: SIEB & MEYER Страницы: 119

TITAN-TRACKSIDE-6

Бренд: RC System Страницы: 4

Бренд: Sensitron Страницы: 32

Бренд: FMS Страницы: 108

Бренд: DS Produkte Страницы: 4

Бренд: GEM Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды